Patton SmartNode 4900 User Manual Download Page 59

Page: 59 / 76

Management

SmartNode 4900 User Manual

B • Specifications

802.1p VLAN tagging

IPSEC AH & ESP Modes

Manual Key; IKE optional

AES/DES/3DES Encryption

Management

Industry standard CLI with local console (RJ-45, RS-232) and remote Telnet access

TFTP configuration & firmware loading

SNMP v1 agent (MIB II and private MIB)

Built-in diagnostic tools (trace, debug)

Operating environment

Temperature

Operating range: 32–104°F (0–40°C)

Internal temperature: Available in real-time on the IpChannel Bank web pages

Humidity

5 to 90% relative humidity (RH), non-condensing

Altitude

Maximum operating altitude: 15,000 feet (4,752 meters)

System

•

The processor is a Motorola MPC875 series 32-bit PowerPC core, 133 MHz

•

8 MB Flash

•

32 MB SDRAM

Dimensions

1.75 inches (4.44 cm) height, standard 19-inch (48.26 cm) width, 12 inches (30.48 cm) depth

Weight and power dissipation

See

table 12

Table 12. SmartNode weight and maximum power specifications

SmartNode model

Weight

Maximum power dissipation

IpChannel Bank 4912

9.1 lb (4.1 kg)

25W

IpChannel Bank 4916

9.1 lb (4.1 kg)

30W

IpChannel Bank 4924

9.1 lb (4.1 kg)

40W

Summary of Contents for SmartNode 4900













































































Search results

Summary of Contents for SmartNode 4900

Reviews:

Related manuals for SmartNode 4900

Brands by name

Popular brands

Patton SmartNode 4900, User Manual

Search results

Summary of Contents for SmartNode 4900

Reviews:

Related manuals for SmartNode 4900

Brands by name

Popular brands