Patton SmartNode 4900 User Manual Download Page 24

Page: 24 / 76

Chapter 3

Hardware installation

Chapter contents

Introduction

..........................................................................................................................................................25

Planning the installation

........................................................................................................................................25

Installation checklist

.......................................................................................................................................26

Site log

............................................................................................................................................................26

Network information

......................................................................................................................................27

Network diagram

......................................................................................................................................27

IP related information

...............................................................................................................................27

Configuration tools

.........................................................................................................................................27

AC Power Mains

.............................................................................................................................................27

Location and mounting requirements

.............................................................................................................28

Installing the IpChannel Bank

...............................................................................................................................28

Unpacking the Model SN4900 series IpChannel Bank

...................................................................................28

IpChannel Bank chassis installation

................................................................................................................28

Connecting cables

...........................................................................................................................................29

Connecting the FXS ports

.........................................................................................................................29

Connecting the FXO ports

........................................................................................................................29

Connecting the Ethernet ports

..................................................................................................................30

Connecting the 10/100Base-T Ethernet ports to an Ethernet switch or hub

........................................ 30

Connecting a 10/100Base-T Ethernet port to an Ethernet-capable workstation

.................................. 31

Connecting the EIA-561 RS-232 configuration port (DCE configured)

...................................................31

Connecting the serial port

.........................................................................................................................31

Connecting power

...........................................................................................................................................32

Grounding the Model SN4900—AC and DC units

.................................................................................32

Installing the power cables—AC units

.......................................................................................................33

Installing the power cables—DC units

......................................................................................................34

Summary of Contents for SmartNode 4900













































































Search results

Summary of Contents for SmartNode 4900

Reviews:

Related manuals for SmartNode 4900

Brands by name

Popular brands

Patton SmartNode 4900, User Manual

Search results

Summary of Contents for SmartNode 4900

Reviews:

Related manuals for SmartNode 4900

Brands by name

Popular brands