Patton SmartNode 4900 User Manual Download Page 56

Page: 56 / 76

Voice connectivity - FXS

SmartNode 4900 User Manual

B • Specifications

Voice connectivity - FXS

2-wire Loopstart, RJ-11/12

Short haul loop 1.1 km @3REN

EuroPOTS (ETSI EG201 188)

Programmable AC impedance, feeding, and ring voltage; on-hook voltage 48 VDC

Caller-ID Type-1/2 FSK and ITU V.23/Bell 202 generation

Voice connectivity - FXO

2-wire Loopstart, RJ-11/12

EuroPOTS (ETSI EG201 188)

Programmable AC terminantion

Programmable DC terminantion

Ethernet interface

The SN4900 series has dual 10/100-Mbps Ethernet ports presented on two RJ-45 connectors supporting:

•

100Base-TX half-/full-duplex operation

•

10Base-TX half-/full-duplex operation

•

Auto detection and fallback

Console port

The RS-232 port provides for initial configuration of the Model SN4900 series. The RS-232 port supports:

•

Asynchronous data rate of 9600 bps, 2 bits, no parity, 1 stop bit, no flow control

•

An RJ-45 connector with EIA-561 (RS-232) pinouts

•

A management interface (such as HyperTerminal) that supports VT-100 terminals

Serial ports

The serial expansion port allows for either a V.35 or X.21 interface depending on the model chosen. This
port supports:

•

V.35 interface presented on DB-25 connector

•

X.21 interface presented on DB-15 connector

•

Data rates up to 2 Mbps

•

Frame Relay or PPP protocols

•

Status and activity LED indicators

Summary of Contents for SmartNode 4900













































































Search results

Summary of Contents for SmartNode 4900

Reviews:

Related manuals for SmartNode 4900

Brands by name

Popular brands

Patton SmartNode 4900, User Manual

Search results

Summary of Contents for SmartNode 4900

Reviews:

Related manuals for SmartNode 4900

Brands by name

Popular brands