Patton SmartNode 4900 User Manual Download Page 57

Page: 57 / 76

FXS ports

SmartNode 4900 User Manual

B • Specifications

FXS ports

The FXS ports provide for connection of up to 32 analog FXS devices on a 50- or 64-pin RJ-21X connector
located on the rear panel.

FXO ports

The FXO ports provide for connection of up to 32 analog FXO devices on a 50- or 64-pin RJ-21X connector
located on the rear panel.

PPP and Frame-Relay support

•

X.21 or V.35 WAN

•

Frame-Relay (8 PVCs)

•

RFC1490, FRF.12 fragmentation

•

LMI, Q.933D, ANSI 617D, Gang of Four (an encapsulation method created by the four companies: Cisco,
Northern Telecom, StrataCom, and DEC which differs from the IETF encapsulation)

•

PPP, PAP, CHAP, LCP, IPCP

Voice processing (signaling dependent)

Voice codecs:

•

G.711 A-Law/ -Law (64 kbps)

•

G.726 (ADPCM 40, 32, 24, 16 kpbs)

•

G.723.1 (5.3 or 6.3 kbps)

•

G.729ab (8 kbps)

•

Transparent pass through

•

G.168 echo cancellation

•

Up to 32 parallel voice connections

•

DTMF detection and generation

•

Carrier tone detection and generation

•

Silence suppression and comfort noise

•

Configurable dejitter buffer

•

Configurable tones (dial, ringing, busy)

•

Configurable transmit packet length

•

RTP/RTCP (RFC 1889)

Fax and modem support

G.711 transparent FAX

Summary of Contents for SmartNode 4900













































































Search results

Summary of Contents for SmartNode 4900

Reviews:

Related manuals for SmartNode 4900

Brands by name

Popular brands

Patton SmartNode 4900, User Manual

Search results

Summary of Contents for SmartNode 4900

Reviews:

Related manuals for SmartNode 4900

Brands by name

Popular brands