background image

33

Product Warranty –

  

SMOG-HOG

®

 and DUST-HOG

®

 Pollution Control Systems

1. Subject to the terms and conditions hereof, Parker-Hannifin Corporation (PARKER) warrants that major structural
components on MCB, PNP, SDC, SFC, and SHM series will be free from defects in materials and workmanship for ten 
(10) years from the date of shipment from Parker. Subject to the terms and conditions hereof, warrants to the original 
Buyer of any Parker product (PRODUCT) installed and used as recommended by PARKER in normal service, that if the 
PRODUCT fails or is materially defective within twenty-four (24) months from date of installation or thirty (30) months from 
the date of shipment (whichever is earlier), of such PRODUCT, then PARKER, at PARKER’S sole option, will replace the 
PRODUCT with the same or equivalent PRODUCT, repair the PRODUCT or refund the  original purchase price for the 
PRODUCT. Such replacement, repair of payment by PARKER shall be in complete satisfaction of any and all liability of 
PARKER and its agents with respect to such PRODUCT. Excluded from any Parker warranty are hose, electrical  
motors or consumable products such as flexible hose, belts, filter cartridges, filter media, ESP cells, electrical  
components, gasketing, or any component defined by PARKER as a consumable item.

2. Parker IGFG’s warranty policy covers defects that are due to manufacturing quality. Equipment must be installed,
commissioned and maintained in accordance with Parker IGFG recommendations as documented in the specific user
manual related to your dust or wet collector product. This warranty does not cover defects due to poor environmental
conditions, improper installation, or wear and tear items. This warranty shall be void in case of:

a) Any buyer’s modifications not explicitly approved by Parker IGFG Division,
b) Misuse or failure in maintenance - not in accordance with Parker’s product recommendations,
c) Use of unauthorized or non-genuine Parker replacement parts,
d) Damage caused by corrosion, abrasion, abnormal use or misuse, misapplication, or normal wear and tear,
e) Equipment not properly installed, operated and maintained under normal conditions and recommended applications.

As Buyers exclusive remedy for any defects in the equipment, Parker will exchange or repair any defective parts during
the warranty period, provided such parts are returned, prepaid, to Parker factory. The obligation of Parker is limited to
furnishing replacement parts EXW Parker factory or making repairs at Parker factory of any parts that are determined,
upon inspection by Parker, to be defective. In no event will Parker be responsible for labor or transportation charges
for the removal, reshipment or reinstallation of the parts. Replacement parts will be provided via INCOTERMS EXW
from Parker’s Lancaster NY location. Parker makes no warranty as to goods manufactured or supplied by others.

3. THE FOREGOING IS THE ONLY WARRANTY, GUARANTEE OR REPRESENTATION OF ANY KIND MADE 
WITH RESPECT TO THE SUBJECT PARKER PRODUCTS. NO IMPLIED WARRANTY, INCLUDING ANY  
IMPLIED WARRANTY OF NONINFRINGEMENT, DESIGN, MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE, APPLIES TO THE PRODUCT, AND NO OTHER EXPRESS WARRANTY OR  
GUARANTY, EXCEPT AS MENTIONED ABOVE, GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH  
RESPECT TO THE PRODUCT SHALL BIND PARKER. PARKER SHALL NOT BE LIABLE FOR LOSS OF  
REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES,  
OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE  
OR INABILITY TO USE THE PRODUCT REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS 
BASED, AND EVEN IF PARKER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL  
RECOVERY OF ANY KIND AGAINST PARKER BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF 
THE PRODUCT SOLD BY PARKER AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE  
FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR 
PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE 
THE PRODUCT NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF PARKER. THIS LIMITED WARRANTY IS 
GIVEN ONLY WITH RESPECT TO A PRODUCT PURCHASED FROM PARKER OR AN AUTHORIZED  
PARKER DISTRIBUTOR.

Summary of Contents for SFC











































Reviews: