background image

27

5.7   ProTura

®

 Nanofiber Cartridge Filters

The SFC product line is designed to accept ProTura

®

 Nanofiber 

cartridge filters. Table 2 highlights the most common Parker 
cartridge filters.
Parker will custom design cartridge filters for application-specific 
systems. Contact the Parker office for additional information.

5.8  Explosion Vent Replacement

5.8.1   Dome Style Explosion Vent Replacement

CUT HAZARD - WEAR PROTECTIVE CLOTHING

1.  In case of explosion, contact Parker immediately. Do not 

operate or rearm the collector with another explosion vent 
membrane without contacting Parker first. Serious injury 
could occur.

2.  Verify that the system is depressurized and safe for human 

exposure before attempting to remove the old or burst 
rupture panel. While loosening the capture frame bolting, take 
care to avoid the sharp edges of the rupture panel as these 
can cause severe cuts and/or abrasions. Remove the capture 
frame and set aside.

3.  After removal of the capture frame, remove the rupture panel. 

This may require bending panel sections away from the frame 
for frame removal. Care should be taken to avoid sharp panel 
edges during this activity.

4.  Dispose of the removed rupture panel in accordance with 

applicable local and federal regulations.

5.  Install the new rupture panel. Make sure all tags and danger 

warnings are placed on the side of the explosion vent facing 
out towards installer. Secure with the appropriate gasket 
material, bolting and previously removed capture frame.

6.  Rupture panels are not bolt torque sensitive; i.e., bolt torque 

does not increase or decrease the rupture panel set pressure. 
The bolt torque used should be only that which is sufficient to 
create a leak-free seal.

!

 

CAUTION

6. Troubleshooting Guide 

Use the troubleshooting guide to correct any problems that 
occur with your dust collection unit. If the problem or condition 
continues, contact the Parker customer service office.

 All electrical/mechanical troubleshooting should be  
performed by a qualified electrician/maintenance ind- 
ividual familiar with Parker equipment.

 Prior to troubleshooting any equipment, read the In-
stallation and Operation Manuals for each piece of 
equipment to be serviced.

!

 

WARNING

Summary of Contents for SFC











































Reviews: