5-4
The Keypad
650G AC Drive
The Menu System
Press
to show following:
Press
to show following:
See chapter 6 for instructions to view full menu
Press
to show following:
This menu is configured by the App
Menu blocks in DSE Lite. Also
applications 3, 4, 5 & 6 populate
this menu as shown.
Press
to show following:
Hz Drive frequency
% Speed setpoint
v DC link volts
A Motor current
To see the following menu
requires detailed menus view
to be enabled:
To enable arrow to
press
arrow to
and
press
key.
Digin word
Anin 1 value
Anin 2 value
Digout word
Anout 1 value
Anout 2 value
Trip 1, (newest)
Trip 2
Trip 3
Trip 4
Trip 5
Trip 6
Trip 7
Trip 8
Trip 9
Trip 10, (oldest)
P
1
Application
P
2
Max speed
P
3
Min speed
P
4
Accel time
P
5
Decel time
P
6
Motor current
P
7
Base frequency
P
8
Jog setpoint
P
9
Run/stop mode
P
11 V/F shape
P
12 Normal duty
P
13 Fixed boost
P
14 Auto boost
P
99 Password
Control mode
Nameplate RPM
Fly-catch enable
Slip comp enable
Stabilisation enable
Voltage control mode
Boost mode
Auto boost
Energy saving
Motor current
Motor poles
Motor voltage
Mag current
Power
Motor connection
Stator resistance
Leakage inductance
Mutual inductance
Rotor time constant
Autotune mode
Autotune enable
Current limit
Positive torque limit
Negative torque limit
Stall trip type
Speed prop gain
Speed integral time
Speed positive limit
Speed negative limit
Digin 1 invert
Digin 2 invert
Digin 3 invert
Digin 4 invert
Digin 5 invert
Digin 6 invert
Digin 7 invert
Anin 1 scale
Anin 1 offset
Anin 1 type
Anin 2 scale
Anin 2 offset
Anin 2 type
Digin 1 value
Digin 2 value
Digin 3 value
Digin 4 value
Digin 5 value
Digin 6 value
Digin 7 value
Anin1 value
Anin2 value
Digout 1 invert
Digout 2 invert
Relay invert
Anout 1 scale
Anout 1 offset
Anout 1 abs
Anout 1 value
Anout 2 scale
Anout 2 offset
Anout 2 abs
Anout 2 value
Digin 1 destination
Digin 2 destination
Digin 3 destination
Digin 4 destination
Digin 5 destination
Digin 6 destination
Digin 7 destination
Digout 1 source
Digout 2 source
Relay source
Anout 1 source
Anout 2 source
4 to 20mA loop
Anin 2 overload
Motor stalled
Moter overtemp
Inverse time
Dynamic brake resistor
Dynamic brake switch
Speed feedback
Over speed
Display / keypad
DC link ripple
Remote comms sel
Comms timeout
Comms address
Comms baud rate
Comms parity
Reply delay ms
Protocol, (OP)
Protocol, (P3)
Jog accel time
Jog decel time
Ramp time
S ramp jerk
S ramp cont
min speed mode
Skep freq 1
Skip freq 1 band
Skip freq 2
Skip freq 2 band
AR attempts
AR delay
AR triggers
AR t
DB Enable
DB Resistance
DB Power
DB Over-rating
Torque feedback
Torque level
Use abs torque
Local min speed
Enabled keys
Application lock
Detailed menus
Encoder mode
Encoder reset
Encoder invert
Encoder lines
Encoder speed scale
Encoder speed
APP menu 1
APP menu 2
APP menu 3
APP menu 4
APP menu 5
APP menu 6
APP menu 7
APP menu 8
APP menu 9
APP menu 10
APP menu 11
APP menu 12
APP menu 13
APP menu 14
APP menu 15
APP menu 16
Default settings
Macro 3:
Preset 0
Preset 1
Preset 2
Preset 3
Preset 4
Preset 5
Preset 6
Preset 7
Macro 4:
RL ramp rate
RL max value
RL min value
RL reset value
Macro 5:
PI P gain
PI I gain
PID D gain
PID D filter TC
PID fbk gain
PID limit
PID low limit
PID symmetric limit
PID scale
PID error
PID output
Macro 6:
Command
Setpoint
Status
Use the arrow down key
to go left and arrow up key
to go right
NOTE:
To move
up and
down the
lists
arrow up
to go
down
and
arrow
down
to go up.
Software Version Number
This is displayed on power-up, for up to 8
seconds. For example, version 5.2:
It can also be displayed by pressing the E
key for 2 seconds when at the top of the
MMI tree, Menu Level 1.
.
