4
Programming Guide
HOW DO I PROGRAM THE SYSTEM?
The
Spectra
TM
series control panels can be programmed using the
WinLoad Software
or by using any keypad connected to
the
Spectra
control panel. For information on the WinLoad Software, please refer to
the Spectra Installation & Reference
Manual
. To program the
Spectra
control panel using a keypad, you must enter the
Programming Mode
as shown below.
Once a control panel has been programmed, you can use the
Paradox Memory Key
to copy the contents from the
programmed control panel to one or more control panels (see page 5).
SINGLE DIGIT DATA ENTRY METHOD
(Hexadecimal and Decimal)
Single Digit Data Entry
is used in all sections except those specified in
Multiple Feature Select Programming
Method
. After
entering the programming mode as described in the shaded box above, some sections will require that you enter
Decimal
values from
000 to 255
. Other sections will require that you enter
Hexadecimal
values from
0 to F
. The required data will be
clearly indicated in this manual. When entering the final digit in a section, the control panel will automatically save and
advance to the next section. With the exception of sections 001 to 016, where after entering the first two digits, the control
panel will switch to
Multiple Feature Select Programming
.
MULTIPLE FEATURE SELECT PROGRAMMING METHOD
Sections: [001] to [016], [127] to [138], [302] to [348], [610], [650] to [651]
After entering the programming mode as described in the shaded box above, each option from
[1]
to
[8]
will represent a
specific feature or option. Press the key corresponding to the desired option and the corresponding light will illuminate or the
option number will appear in the LCD display. This means the option is on. Press the key again to extinguish the
corresponding light or remove the digit from the LCD display, thereby, turning off the option. Please note that pressing the
[
FORCE
]
key will set all 8 options to “off”. Press the keys as many times as you need until all 8 options in the current section
are set. When the options are set, press the
[
ENTER
]
key to save and advance to the next section.
Default Installer Code:
000000
(see section [281] on page 20)
Default System Master Code: 123456
(see section [301] on page 21)
To enter Programming Mode:
STEP 1:
Press
[
ENTER
]
STEP 2:
Enter your
[
INSTALLER
CODE
]
STEP 3:
Enter 3 digits of
[
SECTION
]
you wish to program
STEP 4:
Enter required
[
DATA
]
Table 1: Decimal and Hexadecimal Programming Table
Value or Action
What Do I
Press?
What Do I See?
10-Zone LED
16-Zone LED
LCD
Values 1 to 9
[1] to [9]
[1] to [9]
[1] to [9]
[1] to [9]
A
(hexa only)
[0]
[0
(10)
]
[10]
A
B
(hexa only)
[
STAY
]
[
STAY
]
[11]
B
C
(hexa only)
[
BYP
]
[
BYP
]
[12]
C
D
(hexa only)
[
MEM
]
[
MEM
]
[13]
D
E
(hexa only)
[
TBL
] / [
TRBL
]
[
TBL
]
[14]
E
F
(hexa only)
[
PG
] / [
FNC
1]
[
PG
]
[15]
F
Erase Current Digit
[
FORCE
]
Displays next digit or next section
Exit Without Saving
[
CLEAR
]
[
ENTER
] flashes [
ARM
1
] & [
STAY
1
] flash “SECTION [ ]”
Save Data
(hexa only)
[
ENTER
]
Advances to the next section
