Panasonic VARICAM LT, Operating Manual

Page: 130 / 182

– 130 –
Chapter 10 Menu Operations — Menu list
Item Description of settings
[USER BOX H POS] Sets the horizontal position of the center of the user box.
[ − 50] - [50]
f
Factory setting: [0]
[USER BOX V POS] Sets the vertical position of the center of the user box.
[ − 50] - [50]
f
Factory setting: [0]
[VF SDI FOCUS
ASSIST]
[EXPAND MODE] Sets the enlargement display function mode.
[10SEC]: Disables the enlarged display function after 10 seconds have elapsed.
[HOLD]: Enables the enlarged display function.
[UNTIL REC]: Enables the enlarged display function until performing recording operation.
f
Factory setting: [10SEC]
[EXPAND1 SW] Switches display/hide of the enlargement display function 1.
[ON], [OFF]
f
Factory setting: [OFF]
[- POS1] Adjusts the source signal position in an enlarged display.
[0] - [8]
f
Factory setting: [4]
[- VALUE1] Adjusts the enlargement factor.
[x2], [x3], [x4]
f
Factory setting: [x2]
[EXPAND2 SW] Switches display/hide of the enlargement display function 2.
[ON], [OFF]
f
Factory setting: [OFF]
[- POS2] Adjusts the source signal position in an enlarged display.
[0] - [8]
f
Factory setting: [4]
[- VALUE2] Adjusts the enlargement factor.
[x2], [x3], [x4]
f
Factory setting: [x2]
[FOCUS IN COLOR SW] Displays/hides the peaking function.
[ON], [OFF]
f
Factory setting: [OFF]
[- PEAKING VALUE] Sets the peaking function mode.
[LOW], [MID], [HIGH]
f
Factory setting: [MID]
[- COLOR SEL] Sets the peaking function color.
[RED], [GREEN], [WHITE]
f
Factory setting: [RED]
[- MONO] Switches display/hide of the monochrome function when the peaking function is displayed.
[ON], [OFF]
The monochrome display function is enabled when [MONO SW] is set to [ON] even if this is set to [OFF],
and it will display with monochrome function.
The monochrome display function is enabled when this is set to [ON] even if [MONO SW] is set to [OFF],
and it will display with the monochrome function.
f
Factory setting: [OFF]
[FOCUS SQUARES SW] Displays/hides the focus square function.
[ON], [OFF]
f
Factory setting: [OFF]
[MONO SW] Switches enable/disable of the monochrome display function when [IN COLOR/SQ./MONO SW] is set to
[ON].
[ON], [OFF]
f
Factory setting: [OFF]
[FOCUS DISP] Sets the unit for the focus distance display.
[Meter], [Feet]
f
Factory setting: [Feet]
[VF SDI EI ASSIST] [ZEBRA SW] Sets if the zebra signal is superimposed or not to the output from the <VF SDI> terminal.
[ON], [OFF]
f
Factory setting: [OFF]
[- ZEBRA1 DETECT] Sets the detection level of zebra pattern 1.
[0%] - [109%]
f
Factory setting: [80%]
[- ZEBRA2 DETECT] Sets the extraction level of zebra pattern 2.
[0%] - [109%]
f
Factory setting: [100%]
[- ZEBRA2] Enables/disables zebra pattern 2 and selects [SPOT].
[ON], [SPOT], [OFF]
f
Factory setting: [OFF]
[WFM SW] Displays/hides waveform monitor.
[ON]/[OFF]
f
Factory setting: [OFF]
[- TYPE] Sets the display format of the waveform monitor.
[Y], [YGBR]
f
Factory setting: [Y]