Panasonic VARICAM LT, Operating Manual

Page: 160 / 182

– 160 –
Chapter 11 Network Connection — Network settings
Network settings
Configuration of various settings are required to use the wireless LAN or the wired LAN. Configure the settings according to the function to use.
Wireless LAN settings
This section describes the settings to connect the camera to mobile devices (iPad/iPhone), computers, or wireless access point via wireless LAN.
[DIRECT] mode
Use the following procedures when accessing to the network function of the camera directly from a smartphone, tablet, or computer.
The camera may restart as necessary when the setting is changed.
1
Select [DIRECT] in [MENU] → [PERIPHERAL] → [WIRELESS PROPERTY] → [TYPE].
2
Set each item in [MENU] → [PERIPHERAL] → [WIRELESS PROPERTY] as necessary.
[MAC ADDRESS]: MAC address of wireless LAN (cannot be changed)
[SSID]: Network name of the camera (SSID) ([AU-V35LT1])
[BAND]: Setting for switching between two transmission methods (2.4 GHz or 5 GHz) (Factory setting: [2.4GHz]) (set to [2.4GHz] when AJ-WM30 is
used).
[CHANNEL(2.4GHz)]: Channel used when set to 2.4 GHz (Factory setting: [AUTO])
[CHANNEL(5GHz)]: Channel used when set to 5 GHz (Factory setting: [AUTO])
[ENCRYPTION]: Encryption format to be used (Factory setting: [WPA2-AES])
[ENCRYPT KEY]: WPA2 encryption key (Factory setting: [01234567890123456789abcdef])
[DHCP]: Setting whether to use automatic acquisition via DHCP ( [ENABLE]: Use automatic acquisition/ [DISABLE]: Does not use automatic
acquisition) (Factory setting: [ENABLE]) (cannot be set)
[IP ADDRESS]: IP address of the camera (Factory setting: [192.168.0.1]).
[SUBNET MASK]: Subnet mask (Factory setting: [255.255.255.0])
[DEFAULT GATEWAY]: Default gateway (Factory setting: [192.168.0.254]) (cannot be set)
[PRIMARY DNS]: Primary DNS server setting (Factory setting: [0.0.0.0]) (cannot be set)
[SECONDARY DNS]: Secondary DNS server setting (Factory setting: [0.0.0.0]) (cannot be set)
[DHCP SERVER]: Setting to use the DHCP SERVER function ( [ENABLE]: Use the DHCP SERVER function/ [DISABLE]: Does not use the DHCP
SERVER function) (Factory setting: [ENABLE])
3
Select [WLAN] in [MENU] → [PERIPHERAL] → [NETWORK SEL].
The changed setting will be valid after rebooting the camera.
4
Select SSID from the list of the access points for mobile devices or computers and enter the password (encryption key).
Display the access point list screen in wireless setting and select [SSID] of the camera.
f
Factory setting: [AU-V35LT1]
When the password confirmation screen appears, enter the password (encryption key).
f
Factory setting: [01234567890123456789abcdef]
5
Check the network connection.
When the setting is completed, confirm that network connection of mobile devices (iPad/iPhone) or computers is made properly.
The application using the network can be used when it is correctly connected to the network.
@ @ NOTE
t
AJ-WM30 can only operate when the communication method is 2.4 GHz. It will operate after automatically setting to CH1 of 2.4 GHz when [BAND] is
set to [5GHz].
t
The startup time after turning on the power may be longer due to starting of the network.
t
When you change the settings of [NETWORK SEL], the changes will not be reflected until the camera is restarted. After the settings have been
changed, the setting screen termination may take time due to the restart of the network service.
t
All of the IP address, subnet mask, and default gateway must be correctly set.
If a warning [CANNOT ACCESS GATEWAY!] appears at the termination of the setting screen, contact the administrator of the network you use.
t
If you do not use default gateway and DNS, set them to [0.0.0.0].
t
DHCP and DNS may not function properly depending on the network environment.
[INFRA] mode (when SSID is manually entered)
This is the setting to manually connecting to the wireless access point.
1
Select [INFRA] in [MENU]
→
[PERIPHERAL]
→
[WIRELESS PROPERTY]
→
[TYPE].
2
Set each item in [MENU] → [PERIPHERAL] → [WIRELESS PROPERTY] as necessary.
[MAC ADDRESS]: MAC address of the wireless LAN (cannot be changed)
[BAND]: Setting for switching between two transmission methods (2.4 GHz or 5 GHz) (Factory setting: [2.4GHz]) (cannot be set)
[CHANNEL(2.4GHz)]: Channel used when set to 2.4 GHz (Factory setting: [AUTO]) (cannot be set)
[CHANNEL(5GHz)]: Channel used when set to 5 GHz (Factory setting: [AUTO]) (cannot be set)
[DHCP]: Setting whether to use automatic acquisition via DHCP ( [ENABLE]: Use automatic acquisition/ [DISABLE]: Does not use automatic
acquisition) (Factory setting: [ENABLE])
[IP ADDRESS]: IP address of the camera (Factory setting: [192.168.0.1])
[SUBNET MASK]: Subnet mask (Factory setting: [255.255.255.0])
[DEFAULT GATEWAY]: Default gateway (Factory setting: [192.168.0.254])
[PRIMARY DNS]: Primary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the DNS
server, the DNS server value which is acquired externally is overwritten. When the value is [0.0.0.0], the server is not set.)