Panasonic PN28480K-ID Operation Manual Download Page 154

Page: 154 / 438

154

mac-address-table static <MAC addr.> <interface name> vlan <VLAN ID>

Statically enters a MAC address in the MAC address table.

no mac-address-table static <MAC addr.> vlan <VLAN ID>

Deletes a static MAC address from the MAC address table.

[Parameter]

Parameter name Description

Set the MAC address to be statically entered.

Set the interface name of the target port.

Set the target VLAN ID.

[Factory Default Setting]

Parameter name Factory default setting

None

None

None

[Setting Range]

Parameter name Setting range

00:00:00:00:00:01 to FF:FF:FF:FF:FF:FE

<Switch-M48eG>

GigabitEthernet0/1 to GigabitEthernet0/48

<Switch-M24eG>

GigabitEthernet0/1 to GigabitEthernet0/24

<Switch-M16eG>

GigabitEthernet0/1 to GigabitEthernet0/16

<Switch-M8eG>

GigabitEthernet0/1 to GigabitEthernet0/9

The name can be abbreviated.

Example: GigabitEthernet0/1



gi0/1

1 to 4094

Summary of Contents for PN28480K-ID























































































































































































































































































































































































































































Search results

Summary of Contents for PN28480K-ID

Reviews:

Related manuals for PN28480K-ID

Brands by name

Popular brands

Panasonic PN28480K-ID, Operation Manual

Search results

Summary of Contents for PN28480K-ID

Reviews:

Related manuals for PN28480K-ID

Brands by name

Popular brands