Panasonic PN28480K-ID Operation Manual Download

Page: 400 / 438

400

reboot {default | default-except-ip}

After the system is rebooted, initializes all stored configuration and
system information and restores them to the factory default settings.

[Parameter]

Parameter name

Description

{ default |

default-except-ip}

Specify an option for the reboot type of the
Switching Hub.
Default

Restores to the factory
default settings after reboot.

default-except-ip Restores to the factory

default settings after reboot,
except for the IP address
setting.

[Factory Default Setting]

Parameter name

Factory default setting

None

[Setting Range]

Parameter name

Setting range

None

[Note]

Parameter name

Note

None

Note:

Once initialized, the configuration and system information cannot
be restored. Pay full attention on execution.

Summary of Contents for PN28480K-ID























































































































































































































































































































































































































































Search results

Summary of Contents for PN28480K-ID

Reviews:

Related manuals for PN28480K-ID

Brands by name

Popular brands

Panasonic PN28480K-ID, Operation Manual

Search results

Summary of Contents for PN28480K-ID

Reviews:

Related manuals for PN28480K-ID

Brands by name

Popular brands