Panasonic PN28480K-ID Operation Manual Download Page 224

Page: 224 / 438

224

AccessControl outprofile <index> committed-rate <unit> burst-size <volume>
{deny | permit [dscp <value>]}

Configures the out-profile used for the access control function.

no AccessControl outprofile <index>

Deletes the out-profile used for the access control function.

[Parameter]

Parameter name

Description

<index>

Specify the out-profile index number.

<unit>

Specify the committed rate in Mbps.

Specify the burst size with the burst size
number.

{deny | permit [dscp
<value>]}

Specify whether packets are denied or
permitted.
deny

Packets are denied.

permit Packets are permitted. You can

select the value type from the
following for marking at the
permission.
- DSCP value

[Factory Default Setting]

Parameter name

Factory default setting

None

[Setting Range]

Parameter name

Setting range

<index>

1 to 65535

<unit>

1 to 1000

1 to 5

Select a number from the following to specify
the burst size.
1: 4K, 2: 8K, 3: 16K, 4: 32K, 5: 64K

<dscp-value>

0 to 63

[Note]

Parameter name

Note

None

Summary of Contents for PN28480K-ID























































































































































































































































































































































































































































Search results

Summary of Contents for PN28480K-ID

Reviews:

Related manuals for PN28480K-ID

Brands by name

Popular brands

Panasonic PN28480K-ID, Operation Manual

Search results

Summary of Contents for PN28480K-ID

Reviews:

Related manuals for PN28480K-ID

Brands by name

Popular brands