Panasonic MEW01 351 Planning Manual Download Page 35

Page: 35 / 168

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x



Output no. (0-47)



Properties, like any programmable relay output.

Each input (0-15) has to be added and programmed

via WinG3

regarding:



Input no. (0-15)



Type (of input)



Properties, like any programmable input.

6.5.2

Fan control

Used for Application board type

Fan control

, e.g. "Fan control

application board" 4594, which has a front for Fan control of up to
four fans.

Fan control panel 4593 has two Fan control application boards 4594
and two Fan control fronts (see page 52).

Each Fan (0-3)

(i.e. each Fan control)

has to be added and

programmed

via WinG3.

For each fan (Fan control), also one

I/O unit for fan control 3361

(COM loop unit) has to be added and programmed via WinG3
regarding e.g:



Technical address (COM loop address 1-255)



Name (Fan control I/O unit - normally not changed)



Fan control information



I/O Matrix fan control (Fan control / fan 0-3)



Supervised

not supervised (Input In0)



Output latched

not latched



Enhanced fan control function

not.



Fault detection time (Input In0; 30-255 seconds)



Properties, like any programmable output.



Normally stopped

Normally running

6.5.3

Zone control

Used for Application board type

Zone control

Each input (0-15) has to be programmed

via WinG3 regarding:

Zone control is normally used on the Australian market only.

Summary of Contents for MEW01 351









































































































































































Search results

Summary of Contents for MEW01 351

Reviews:

Related manuals for MEW01 351

Brands by name

Popular brands

Panasonic MEW01 351, Planning Manual

Search results

Summary of Contents for MEW01 351

Reviews:

Related manuals for MEW01 351

Brands by name

Popular brands