Panasonic MEW01 351 Planning Manual Download Page 163

Page: 163 / 168

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

161

Item

C.i.e.

System

General fire alarm via progr. input

250

External fault via progr. input

Programmable outputs (= control
expressions)

148

512

Addressable 2 voltage outputs unit
3364

Interlocking Combinations

200

1000

149

Presentation numbers / alarm points

150

that can be presented in the display(s)
in case of fire alarm

512

Presentation numbers

150

that can be

programmed

512

30 x 512 =

15 360

Zones

151

that can be programmed

512

152

Faults

300

Disabled zones

512

Disabled alarm points (zone/address) +
Disabled COM loops

200

153

Disabled outputs

200

154

Disabled interlocking outputs

200

155

Sensors activating SERVICE signal

100

Max. number of AAF zones

(Max. 5 detectors per AAF zone.)

156

100

148

Approx. 4000 trigger conditions can be used in these control expressions.

149

Max. 100 user definable texts can be displayed "at the same time".

150

Presentation number is a ZONE only or ZONE – ADDRESS.

151

Any zone number between 001 and 999 can be used for the 512 zones.

152

Theoretically 999 zones can be programmed but according to EN54-2 it

shall be possible to present all "fire alarms" in the display, i.e. max. 512.

153

Zone/address disabled via time channel not included.

154

Control outputs disabled via menu H2/B7 and Alarm devices disabled via

menu H2/B8 not included.

155

Interlocking outputs disabled via menu H2/B7 not included.

156

Used in conjunction with the AAF Control, which is available on the

Australian market only.

Summary of Contents for MEW01 351









































































































































































Search results

Summary of Contents for MEW01 351

Reviews:

Brands by name

Popular brands

Panasonic MEW01 351, Planning Manual

Search results

Summary of Contents for MEW01 351

Reviews:

Brands by name

Popular brands