Panasonic MEW01 351 Planning Manual Download Page 151

Page: 151 / 168

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

149

COM loop units (input / display units)

Normal state

(quiescent) (mA)

Alarm state

(activated) (mA)

Analog heat detector 3308 + analog base 3312xx

130

0.3

2.3

Analog heat detector, enclosed 3309

130

0.2

1.7

Analog multi detector 4300 + analog base 3312xx

130

0.3

2.3

Analog smoke detector 4301 + analog base 3312xx

130

0.3

2.3

Addressable manual call point 3333 / 3339

Alarm Acknowledge Facility Control (AAFC)

131

Addressable base station for wireless units 4610

132

NOTE!

On each COM loop, up to 5 sensors / detectors can have their LEDs lit at the same time.

COM loop units (output units, etc.)

Normal state

(quiescent) (mA)

Alarm state

(activated) (mA)

Analog base with isolator 4313

133

< 1.3

Addressable multipurpose I/O unit 3361

2.2

max. 12

134

Addressable 2 voltage outputs unit 3364

135

(Addressable) External power supply 3366

<15

Addressable siren 3377

max. 13

Addressable sounder base 3379

0.75

max 3

Addressable beacon 4380

1.7

4-5

I/O matrix board 4582

max. 6

Fan control application board 4594

136

4-6

130

Extern LED current consumption. 2218: add 1 mA.

Analog base with isolator 4313 can be used instead of Analog base 3312.

132

24 V DC power supply also required.

132

24 V DC power supply also required.

133

Detector not included.

134

Only if the input In 0 is used as a zone line input, else approx. 2.2 mA.

135

External 24 V DC power supply also required, e.g. the 3366 unit.

136

Two 4594 boards are mounted on a Fan control panel 4594. 24 V DC

power supply also required.

Summary of Contents for MEW01 351









































































































































































Search results

Summary of Contents for MEW01 351

Reviews:

Related manuals for MEW01 351

Brands by name

Popular brands

Panasonic MEW01 351, Planning Manual

Search results

Summary of Contents for MEW01 351

Reviews:

Related manuals for MEW01 351

Brands by name

Popular brands