Panasonic i-Pro WV-SW355 Operating Instructions Manual Download Page 119

Page: 119 / 130

118

119

Log indications relating to HTTPS

Category

Indication

Description

HTTPS

Self-signed Certificate - Generated

• Generation of the self-signed certificate is com

plete.

Self-signed Certificate - Deleted

• Deletion of the self-signed certificate is complete.

Certificate Signing Request -
Generated

• Generation of the CSR (Certificate Signing

Request) is complete.

CA Certificate - Installed

• Installation of the server certificate is complete.

CA Certificate - Deleted

• Deletion of the server certificate is complete.

Previous CRT key - Applied

• Previous CRT key is applied.

CRT key - Generated

• Generation of the CRT key is complete.

Log indications relating to login

Category

Indication

Description

User name or IP address

• The login user name will be displayed when "On"

is selected for "User auth.".

• The IP address of the PC currently accessing to

the camera will be displayed when "On" is

selected for "Host auth.".

Summary of Contents for i-Pro WV-SW355



































































































































Search results

Summary of Contents for i-Pro WV-SW355

Reviews:

Related manuals for i-Pro WV-SW355

Brands by name

Popular brands

Panasonic i-Pro WV-SW355, Operating Instructions Manual

Search results

Summary of Contents for i-Pro WV-SW355

Reviews:

Related manuals for i-Pro WV-SW355

Brands by name

Popular brands