background image

EBL512 G3 V. 3.0.X 

 - FIRE ALARM SOLUTIONS OPERATING INSTRUCTIONS

97

30.2.  DISABLEMENT BY TIME CHANNEL (H4/U2)

This is a static list of all disablements by time channels in the system. The list has up to four items per page. Indicated by LED 

"General disablements".

a)  Log on to the c.i.e.

b)  Navigate to menu U2.

c)  Scroll in the list with   

.

30.3.  OPEN DOORS (H4/U3)

If any door in the system is open the following symbol is shown in the display: 

 

See also chapter 

17. OPEN DOOR

 on page 35

.

This menu is a dynamic list of all open doors in the system.

a)  Log on to the c.i.e.

b)  Navigate to menu U3.

c)  Scroll in the list with   

.

Zone XXX address XX disabled by time

Channel

Zone XXX address YY disabled by time

channel.

Number of disablement by time channel: 2

d)  To exit the menu press ESC

.

d)  To exit the menu press ESC

.

All other disablements are listed in menu H4/U1.

Door open control unit 00

yyyy-mm-dd  hh:mm

Door open control unit 01

fire brigade panel 00

yyyy-mm-dd  hh:mm

Open door 1 of 2

Summary of Contents for EBL512 G3 5000







































































































































Reviews: