82
VQT4W60
Messages
§
The message are alternately displayed.
On the Unit’s Display
H
∑∑
, F
∑∑
(
“
∑
”
stands for a service number.)
≥
An error has occurred. The number following “H” or “F” depends on the status
of the unit. Check the items below and in the Troubleshooting Guide. If the
service number still does not disappear after the check, reset the unit (
>
84, To
restore the unit if it freezes).
≥
If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
DVD
(
“
∑
”
stands for a number.)
≥
The remote control and the main unit are using different codes. Change the
code on the remote control. (
>
84)
GUIDE
≥
GUIDE Plus+ data is being downloaded. (
>
76)
HARD ERR
§
≥
If there is no change after turning the unit on and off, consult the dealer where
the unit was purchased.
NoERAS
≥
You cannot delete items on this disc.
≥
The disc may be damaged. Use a new disc.
NoREAD
≥
The disc is dirty or badly scratched. The unit cannot record, play, or edit.
≥
The disc may be incompatible or of poor quality. (
>
15, 16)
≥
You have used a lens cleaner and it has finished operation. Press [
<
OPEN/
CLOSE] on the main unit to eject the disc. (
>
7)
NoWRIT
≥
You cannot write to this disc.
The disc may be damaged. Use a new disc.
FINAL
≥
When the screen asking if you want to finalise the disc appears, the message is
displayed. (
>
26)
PLEASE WAIT
§
≥
Displayed when the unit is started. This is not a malfunction.
≥
The unit is carrying out its recovery process. You cannot operate the unit while
the message is displayed.
PROG FULL
§
≥
There are already 32 timer recording programmes. Delete unnecessary timer
recording programmes. (
>
31)
REMOVE
≥
The USB device is drawing too much power. Remove the USB device and turn
the unit off.
SW-DL
≥
The unit is performing a software update. (
>
76)
SP 35:50, LP 151h
“
SP
”
,
“
LP
”
and the numbers are examples.
≥
Available space on the HDD or disc. The example “SP 35:50” is displayed
when less than 100 hours are available and the example “LP 151h” is displayed
when over 100 hours are available.
“SP” and “LP” are recording modes, “35:50” means “35 hours 50 minutes” and
“151h” means “151 hours”.
UNSUPPORT
§
≥
You have inserted a disc the unit cannot play or record onto. (
>
15, 16)
≥
You tried to operate with a non-compatible USB memory. (
>
17)
UNFORMAT
§
≥
You inserted an unformatted DVD-RAM, DVD-RW, +RW, an R, +R DL
or DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted. (
>
26)
EXT-L
≥
This unit is in EXT LINK standby. EXT LINK has been turned on and will stop
operation on the unit until the recording has completed.
Press [EXT LINK] to stop recording or cancel linked timer. (
>
28)
F74
≥
The HDMI connection could not be authenticated due to a transfer malfunction.
If you have another HDMI cable, try to use it. If it remains displayed, consult the
dealer where the unit was purchased.
F75
≥
The HDMI connection could not be authenticated due to an internal data
malfunction. If you have another HDMI cable, try to use it. If it remains
displayed, consult the dealer where the unit was purchased.
U59
≥
The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation when installing the unit. Do not block the
cooling fan on the rear of the unit.
U61
≥
(When a disc is not inserted) Displays when a malfunction has occurred. This is
displayed when the unit is in the recovery process to return to normal operation. Once
the display disappears you can use the unit again.
If it remains displayed, consult the dealer where the unit was purchased.
U76
≥
HDMI cannot be output because this unit is connected to a model that does not
support copyright protection.
DMR-EX86EB_VQTXXXX-B.book 82 ページ ２０１３年３月６日 水曜日 午後４時２６分
