Panasonic AWRP605P - MULTI FUNCTION CONTROLLER, Operating Instructions Manual

Page: 24 / 46

9. Turn the menu setting control (main), and set it so that
the following item appears on the LCD panel.
<Note>
When component signals have been set as the video
input signals, the output signals from the convertible
camera will be switched to Y/C signals, and
chrominance signals will be output from the Pr OUT
connector. When another item on the menu is selected,
the output signals will be switched to the component
signals.
10. Adjust the frequency response using the menu setting
control (R) in such a way that the burst level appearing
on the waveform monitor is set to 40 IRE (0.286V).
Repeatedly adjust the luminance signal and frequency
response until the signal waveforms shown below are
matched.
<Note>
In the luminance and chrominance signal adjustments
performed by the multi-function controller, the level
cannot be reduced below the level of the input signals
from the camera.
It may not be possible to perform these adjustments if
the length of the cables from the pan-tilt heads to the
main unit of the multi-function controller is too short.
C CA AB BL LE E C CO OM MP P M MA AN NU UA AL L
f f R Re es sp po on ns se e : : 0 0
24
Operation
When component signals are used
1. Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Connect a waveform monitor to the VIDEO/Y OUT
connector on the main unit corresponding to the pan-tilt
head system currently selected.
3. Press the MODE button to establish the BAR mode and
switch the output signals from the convertible camera to
color bar signals.
4. Press the MENU button, turn the menu setting control
(main), and set it so that the CABLE COMP item
appears at the top of the LCD panel.
5. Press the OK button.
The following item appears on the LCD panel.
6. Turn the menu setting control (main), and set it so that
the following item appears on the LCD panel.
<Note>
When composite signals have been set as the video
output signals, the video output signals will be switched
to component signals.
When another item on the menu is selected, the output
signals will be switched to the composite signals.
7. Adjust the luminance signal using the menu setting
control (R) in such a way that the level of the white area
appearing on the waveform monitor is set to 100 IRE
(0.714V).
C CA AB BL LE E C CO OM MP P M MA AN NU UA AL L
Y Y L Le ev ve el l : : 0 0
C CA AB BL LE E C CO OM MP P A AU UT TO O
S ST TA AR RT T? ?
n
O OK K K Ke ey y
C CA AB BL LE E C CO OM MP P
n
O OK K K Ke ey y
11. Select the next pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button, and
continue adjusting the cable compensation in each
system concerned.
100
IRE
90
80
70
60
50
40
30
20
10
0
–10
–20
–30
–40
+100
+7.5
100 IRE
(0.714 V)
Waveform monitor
CONTROL/PREVIEW MONITOR OUT SEL
AUX 1 2 3 4 5
TALLY
TRACING MEMORY
LAMP
MENU
LIMIT
OFF
LIMIT
ON
FULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT
R/B
GAIN/PED
WHITE
BAL
AWC
GAIN
MODE
CLOSE WIDE NEAR
DATA SET
TR/PSET M.LOCK
MEMORY
IRIS
IRIS
IRIS
OPEN
ZOOM
TELE
FOCUS
FAR
CALL
INCOM
LEVEL
FOCUS
OPEN
FAR
TELE
OFF
ON
OPERATE
WIDE
ZOOM/FOCUS/IRIS
ABC
ATW
A
B
NG
OK
START/STOP RESTORE RESET
DEF WIP H/F EXT ND OPTION
PAN/TILT SET
CAMERA CONTROL
TRACING/PRESET MEMORY
IRIS
SPEED
PRIORITY
FOCUS
BAR
CAM
TR
PSET
LOW
HIGH
AUTO
MANU
AUTO
MANU
LOCK
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 130
31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50
DOWN
PA N / T I LT / F O C U S / I R I S
U P
L R
CLOSE
NEAR
OPEN
FAR CLOSE
NEAR
4 7•10 3
4•6•9
5
1
100
IRE
90
80
70
60
50
40
30
20
10
0
–10
–20
+20
–20
+20
–20
–30
–40
40 IRE
(0.286 V)
Waveform monitor
8. Connect the VIDEO/Y OUT connector on the main unit
to the external reference input connector on the
waveform monitor, and connect the Pr OUT connector
on the main unit to the video signal input connector on
the waveform monitor.