20
Parts and their Functions
：
Shooting and Recording/Playback Functions Section
32.
DVCPRO/DV connector
This is an in/output connector for video, voice, and
data that comply with the IEEE1394 standard.
Notes
z
Power is not supplied from the unit.
z
Be absolutely sure to bear the following points in
mind when connecting the IEEE1394 cable (DV
cable).
Ensure that the connections with other devices are
made on a 1:1 basis.
When a DV cable has been connected to the DV
connector, do not apply any strong external force
as this may damage the connector.
When error code 1394 E-92 (1394 INITIAL
ERROR) appears, disconnect the connecting
cables and re-connect them or turn off the
camera-recorder’s power and turn it back on.
Ensure that the unit and all of the connected
devices are each grounded (or connected to a
common ground) before use.
If it is not possible to ground the unit and devices,
turn off the power of the unit and of all the
connected devices before connecting or
disconnecting the IEEE1394 cable.
When the unit is to be connected to a device
equipped with a 4-pin type of connector, connect
the unit’s connector (6-pin type) first.
When connecting the unit
with a PC equipped with
a 6-pin type ofconnector,
connect the 1394 cable
as dictated by the shapes
of the 1394 connectors.
Bear in mind that
inserting a plug the wrong way round may damage
the unit.
33.
REMOTE (remote control) connector
The remote control unit AJ-RC10G (optional
accessory) is connected here.
34.
OPTION SLOT
Attach the video encoder card (AJ-YAX800G,
optional). For information about the installation and
proxy recording, see the AJ-YAX800G instruction
manual.
35.
SD memory card insertion slot
An SD memory card (optional accessory) is inserted
here. It is used for metadata upload and proxy
recording (optional).
<Cautions in using SD memory cards>
Insert an SD memory card which is compliant with the
SD card standard into camera-recorder for use.
MultiMediaCard and SDHC memory cards cannot be
used. (Bear in mind that taking pictures may no longer
be possible if you do use them.)
If you intend to use miniSD cards in camera-recorder,
always install the adapter specially designed for
miniSD cards. (The unit will not work properly if only
the miniSD card adapter is installed. Make sure that
the card has been installed in the adapter before using
it.)
Use of Panasonic’s SD memory cards and miniSD
cards is recommended. Be sure to format cards using
camera-recorder.
To format SD memory cards using a personal
computer, download the dedicated software from the
support site.
SD memory cards with the following capacity (8MB -
2GB) can be used for camera-recorder:
For proxy recording (optional), 256MB, 512MB, 1GB or
2 GB SD memory cards with “High Speed” indication
should be used.
For the latest information not available in the operating
Instructions, visit the P2 Support Desk at the following
Web sites.
36.
BUSY (operation mode display) lamp
This lamp indicates the active status of the SD
memory card.
It stays illuminated when the card is active.
Note
While the lamp is on, do not insert or remove the card.
6-pin type
4-pin type
8 MB
16 MB
32 MB
64 MB
128 MB
256 MB
512 MB
1 GB
2 GB
https://eww.pavc.panasonic.co.jp/pro-av/
z
The SDHC card conforms to a new standard for memory
cards with a large capacity of more than 2 GB which was
established by the SD Association in 2006.
z
The SD card logo is a registered trademark.
z
MMC (MultiMediaCard) is a registered trademark of Infineon
Technologies AG.
#,*2:2836&'DQQMࡍࠫ㧞㧜㧜㧢ᐕ㧝㧞㧝㧞ᣣޓἫᦐᣣޓඦ೨㧥ᤨ㧡㧤ಽ
