Panasonic AJ-D400 Service Manual Download

Page: 63 / 104

2-46

3-32. LISTA Sensitivity Adjustment and Sensitivity Detection

ATF ERR

TEST POINT

HSW
GND

Refer to item “2. Table of Test Point” and [LISTA Adjustment Mode] on “Table of
Test Point”.

VTR MODE

PLAY

ADJ. MODE

Select the mode according to adjusting Heads and adjustment mode.
Refer to [LISTA Adjustment Mode] on “Table of Test Point”.

ADJUST

(ATF GAIN)

Select the mode according to adjusting Heads and adjustment mode.
Refer to [LISTA Adjustment Mode] on “Table of Test Point”.

TAPE

Type

Tape

A, D, J

NTSC : VFM3581KM (LISTA), PAL : VFM3681KM (LISTA)
VFM3000EDS (DV LISTA : When use the DV compatible mode Adj..)

B, E, F, G, H, I

NTSC : VFM3581KM (LISTA), PAL : VFM3681KM (LISTA)

NTSC : VFM3581KL (LISTA), PAL : VFM3681KL (LISTA)

<Classified list for Sensitivity Adjustment>

Type

Models

AJ-D440, AJ-D450, AJ-D640, AJ-D650, AJ-D750, AJ-D850

AJ-D400, AJ-D610, AJ-D700, AJ-D700A, AJ-D800, AJ-D800A, AJ-D810, AJ-D810A

AJ-D200, AJ-D210, AJ-D215

AJ-LT75, AJ-LT85

AJ-D220, AJ-D230, AJ-D230, AJ-D230H

AJ-D780, AJ-DE77

AJ-D950, AJ-D950A

AJ-D90, AJ-D900W, AJ-D900WA, AJ-D910WA, AJ-PD900W, AJ-PD900WA

AJ-D92, AJ-D94, AJ-D95DC

AJ-D940

<Specification of confirmation and Adjustment according to Models>

Adjustment Heads and Sensitivity Value (mV/

Type

Normal (25M Model

→

25M, 50M Model

→

50M)

25M Compatible (50M)

DV Compatible

R/P

Head

PB (L)

Head

PB (R)

Head

DVL

Head

R/P

Head

R/P

Head

DVR

Head

A, D

150 ± 15

-----

130 ± 30

-----

B, C

100 ± 10

-----

E, F

150 ± 15

-----

G, I

150 ± 15

-----

150 ± 15

-----

100 ± 10

-----

100 ± 10

-----

100 ± 10

150 ± 15

-----

200 ± 20

Summary of Contents for AJ-D400









































































































Search results

Summary of Contents for AJ-D400

Reviews:

Related manuals for AJ-D400

Brands by name

Popular brands

Panasonic AJ-D400, Service Manual

Search results

Summary of Contents for AJ-D400

Reviews:

Related manuals for AJ-D400

Brands by name

Popular brands