Panasonic AJ-D400 Service Manual Download

Page: 55 / 104

2-38

3-29. LISTA Adjustment Procedure

With procedure of LISTA adjustment, which is
difference of each models. Please select the number
of corresponded procedure follow the below Table 3-
29-1. And when execute the LISTA Adjustment,
please adjust each items follow the flow chart.

<Classified list of LISTA Adjustment Procedure>

Procedure

Models

Procedure (1)

AJ-D200, AJ-D210, AJ-D215,
AJ-D220, AJ-D230, AJ-D230H,
AJ-D250, AJ-D400, AJ-D700,
AJ-D700A, AJ-D800, AJ-D800A,
AJ-D810, AJ-D810A, AJ-D610

Procedure (2)

AJ-D440, AJ-D450, AJ-D640,
AJ-D650, AJ-D750, AJ-D850,
AJ-LT75, AJ-LT85

Procedure (3)

AJ-D90, AJ-D900W, AJ-D900WA,
AJ-D910WA, AJ-PD900W,
AJ-PD900WA

Procedure (4)

AJ-D92, AJ-D94, AJ-D95DC
AJ-D950, AJ-D950A

Procedure (5)

AJ-DE77, AJ-D780

Procedure (6)

AJ-D940

Table 3-29-1

NOTE :
1. Refer to the item “3-32. LISTA Sensitivity

Adjustment & Detection” about procedure of the
sensitivity adjustment and sensitivity detection.

2. Refer to the item “3-33. LISTA Linearity

Adjustment & Waving Measurement” about
procedure of the linearity adjustment.

Procedure (1)

(25M Camera Recorder, Desk-top)

Connection & Boot Up

START

Sensitivity Adjustment

Sensitivity Detection

END

Linearity Adjustment

Waving Measurement

Sensitivity Adj. R/P Head

Linearity Adjustment

Summary of Contents for AJ-D400









































































































Search results

Summary of Contents for AJ-D400

Reviews:

Related manuals for AJ-D400

Brands by name

Popular brands

Panasonic AJ-D400, Service Manual

Search results

Summary of Contents for AJ-D400

Reviews:

Related manuals for AJ-D400

Brands by name

Popular brands