Panasonic AJ-D400 Service Manual Download

Page: 83 / 104

3-8

Figure. 1-7

1-8. Supply Brake Solenoid

Replacement and Adjustment
(except Camera Recorder)

<CHART B>

Model Type

TYPE A

TYPE B

Connector (A)

P15

P2015

P.C.Board (B)

MECH I/F

SERVO

(Removal)
1. Disconnect the connector (A) on the P.C.Board

(B). (Refer to above chart.)

2. Unscrew the 2 screws (A) and remove the Supply

Brake Solenoid Base Unit as shown in Figure 1-
8-1.

3. Unscrew the 2 screws (B) and remove the supply

Brake Solenoid from Supply Brake Solenoid
Base Unit as shown in Figure 1-8-1.

Figure. 1-8-1

(Installation)
1. Install the new supply Brake Solenoid follow the

removal steps in reverse order.

NOTE :
Hang on the Brake Arm Spring as shown in Figure 1-
8-1.

2. After installing, execute the position adjustment

as following procedures.

(Adjustment Procedures)
1. Place the reels in the M cassette size position.
2. Observe the clearance (A) between Brake pad

and it’s turntable as shown in Figure 1-8-2. And
make sure that it is within 0.2 to 0.5mm.

3. If not, loosen the 2 screws (A), which fixed supply

and Take Up Brake Solenoid Unit. And adjust the
position of Brake Solenoid Unit by moving arrow
direction so that the clearance (A) is within
specification. And tighten the 2 screws (A).

4. After adjustment, change the reel position to S

and L cassette size, and confirm that the
clearance (A) is within specification.

SUPPLY BRAKE
SPRING

Summary of Contents for AJ-D400









































































































Search results

Summary of Contents for AJ-D400

Reviews:

Related manuals for AJ-D400

Brands by name

Popular brands

Panasonic AJ-D400, Service Manual

Search results

Summary of Contents for AJ-D400

Reviews:

Related manuals for AJ-D400

Brands by name

Popular brands