Panasonic AJ-D400 Service Manual Download

Page: 85 / 104

3-10

1-10. Pinch Solenoid Replacement

CHART B

Model Type

TYPE A

TYPE B

TYPE

C,D

Connector (A)

P20

P2020

P610

P.C.Board (B)

MECH

I/F

SERVO

(Removal)
1. Disconnect the connector (A) on the P.C.Board

(B). (Refer to above chart)

2. Unscrew the 2 screws (A) and remove the Pinch

Solenoid Unit as shown in Figure 1-10.

3. Unscrew the 2 screws (B) and remove the Pinch

Solenoid Angle as shown in Figure 1-10.

4. Unscrew the 2 screws (C) and remove the Pinch

Solenoid from the Pinch Solenoid Base.

(Installation)
1. Install the new Pinch Solenoid follow the removal

steps in reverse order.

2. After installation, execute the Pinch Solenoid

Position Adjustment.

Figure 1-10

1-11. Pinch Solenoid

Position

Adjustment

SPEC.

T = 0.3 mm

TEST

Gap T

ADJUST

Screw (A) and Hole (B)

MODE

EJECT (Power OFF)

TOOL

Eccentric Driver (VFK0357)

1. Confirm the power of condition at VTR turn to

OFF.

2. Push the pinch roller by hand to be close to

capstan.

3. Push the pinch solenoid by hand so that the

pinch roller contacts capstan.

4. Loosen the two screws (A) and adjust the hole

(B) by VFK0357 so that gap (T) is within
specification.

5. The position for confirm Gap, which is located

spring scratch to Plate (C) side.

Figure 1-11

Summary of Contents for AJ-D400









































































































Search results

Summary of Contents for AJ-D400

Reviews:

Related manuals for AJ-D400

Brands by name

Popular brands

Panasonic AJ-D400, Service Manual

Search results

Summary of Contents for AJ-D400

Reviews:

Related manuals for AJ-D400

Brands by name

Popular brands