PalatiumCare Palcare PAL-211401 Install Manual Download Page 49

Page: 49 / 64

PalatiumCare, Inc.

Page 49

2018

site.signal.locationMargin

Optional Setting

Default Value

Summary

Maximum difference in device signal strengths for locating.

Description

This is the maximum difference in

devices’

signal strength from a

wireless receiver and or wireless repeaters to be considered

equidistant.

site.signal.locationRcvrMarginReduce

Optional Setting

Default Value

Summary

Amount to remove from a device’s wireless receiver signal

strength.

Description

Often devices have higher signal strength from a wireless receiver. By
reducing the wireless receiver signal strength, from a devices signal, it

will help balance device locating. Range value from 0 to 100.

site.system.ignore.lowbattery

Optional Setting

Default Value

Summary

Are all Low Battery messages to be ignored?

Description

This will prevent Low Battery signals from being recorded on the

Maintenance Report. 1 = Yes, 0 = No

site.system.ignore.tamper

Optional Setting

Default Value

Summary

Should Tamper Message be Ignored?

Description

This is used to ignore all system tamper messages. 1 = Yes, 0 = No

site.tampger.recordAagainMins

Optional Setting

Default Value

1440

Summary

The number of minutes to record tampers signals again.

Description

This is number of minutes to wait between recording tamper signals

that show up in the maintenance report.

Summary of Contents for Palcare PAL-211401




























































Search results

Summary of Contents for Palcare PAL-211401

Reviews:

Brands by name

Popular brands

PalatiumCare Palcare PAL-211401, Install Manual

Search results

Summary of Contents for Palcare PAL-211401

Reviews:

Brands by name

Popular brands