PalatiumCare Palcare PAL-211401 Install Manual Download | Manualshive

Page: 13 / 64

background image

Copyright © 2018

PalatiumCare, Inc.

Page 13

2018

Mounting the Required Hardware

Mounting the PalatiumCare Enterprise Server

1.

Secure the Enterprise Server with a screw on each side as shown below. Do not tighten
the screws too tight. Tighten just enough so the server is snug to the System Mounting
Board or to the wall.

2.

Plug the Ethernet cable into the server and route the cable to the PC network port.

3.

Plug the server power connector 5-24 VDC into the Battery Back-up.

4.

Plug the Power and Network Coordinator connector into the server with the black and
white leads.

5.

The connector with the black lead from the server goes to the Battery Back-up.

6.

The connector with the white lead goes into the Network coordinator for wires
connection as shown in the Network Coordinator wiring and connections.

7.

Plug the Serial cable into the Paging Transmitter port on the server and connect it to the
Paging Transmitter.

Figure 1.3

«
...
11
12
13
14
15
...
»

Summary of Contents for Palcare PAL-211401

































































Reviews:

No comments

Related manuals for Palcare PAL-211401

Brand: B&B Pages: 55

Brand: TP-Link Pages: 16

FlexWATCH 1110L

Brand: Seyeon Technology Pages: 96

eServer xSeries 335 Type 8676

Brand: IBM Pages: 178

PRIMERGY BX620 S5

Brand: Fujitsu Pages: 50

PRIMERGY BX620 S4

Brand: Fujitsu Pages: 81

PRIMERGY BX900 S1

Brand: Fujitsu Pages: 46

PRIMERGY BX620 S6

Brand: Fujitsu Pages: 56

Primergy BX920 S4

Brand: Fujitsu Pages: 66

PRIMERGY BX920 S2

Brand: Fujitsu Pages: 70

PRIMERGY BX920 S2

Brand: Fujitsu Pages: 102

PRIMERGY BX400 S1

Brand: Fujitsu Pages: 60

PRIMERGY BX900 S1

Brand: Fujitsu Pages: 144

Primergy BX900 S2

Brand: Fujitsu Pages: 108

PRIMERGY BX600 PG-LNB101

Brand: Fujitsu Pages: 28

PRIMERGY BX600 S3

Brand: Fujitsu Pages: 103

PRIMERGY BX620 S5

Brand: Fujitsu Pages: 96

PRIMERGY BX600 S2

Brand: Fujitsu Pages: 173

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands