OXE OXE-150 HP Installation Manual Download Page 23 | Manualshive

Page: 23 / 68

background image

23

OXE 150/200 HP INSTALLATION MANUAL

Right hand propellers are considered standard rotation propellers. When propelling
a boat forward, the propeller rotates in a right-hand (clockwise) direction as
viewed from the rear.

Left hand propellers are considered counter-rotation propellers. When propelling
a boat forward, the propeller rotates in a left-hand (counterclockwise) direction as
viewed from the rear.

!

WARNING

For multi-outboard applications, always ensure that propellers are installed
on the correct engines before aggressively operating the boat. Refer to
section

Mounting the outboard

.

Engine rotation direction is achieved by the transmission?

PROPELLER SELECTION

«
...
21
22
23
24
25
...
»

Summary of Contents for OXE-150 HP





































































Reviews:

No comments

Related manuals for OXE-150 HP

Brand: Gigabyte Pages: 93

Brand: DFI Pages: 104

Brand: Supero Pages: 92

Brand: TOHATSU Pages: 7

Brand: Fujitsu Siemens Computers Pages: 42

Brand: Gigabyte Pages: 120

Brand: Intel Pages: 110

Brand: BESTEK Pages: 45

Brand: Merit Pages: 4

Brand: ECS Pages: 66

Brand: Avalue Technology Pages: 80

Brand: Alinx Pages: 29

Brand: Texas Instruments Pages: 16

Brand: Shenzhen Pages: 87

Brand: JMD Pages: 23

Outboard Motor BF15A

Brand: Honda Pages: 94

Brand: Honda Pages: 162

Brand: Honda Pages: 737

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands