OXE OXE-150 HP Installation Manual Download Page 10 | Manualshive

Page: 10 / 68

background image

10

OXE 150/200 HP INSTALLATION MANUAL

AVOIDING FUEL FLOW RESTRICTIONS

!

WARNING

Adding components to the fuel supply system as in filters, valves, fittings,
etc. may restrict the fuel flow and could cause engine stalling at low speed,
and/ or a lean fuel condition at high RPM, that could cause engine damage.

SELECTING ACESSORIES FOR THE OUTBOARD

Genuine Cimco Marine Parts and Accessories have been specifically designed and
tested for this outboard.

Some accessories not manufactured or sold by Cimco Marine are not designed to
be safely used with this outboard or outboard operating system. Acquire and read
the Installation, Operation, Maintenance and Accessories manuals for all selected
accessories.

IMPORTANT INFORMATION

«
...
8
9
10
11
12
...
»

Summary of Contents for OXE-150 HP





































































Reviews:

No comments

Related manuals for OXE-150 HP

Brand: Vox Pages: 23

Brand: ECS Pages: 64

Brand: Atmel Pages: 30

Brand: IEI Technology Pages: 160

Brand: Texas Instruments Pages: 11

Brand: ASROCK Pages: 160

Brand: DFI Pages: 44

Brand: TYAN Pages: 96

Brand: Lite-on Tech Pages: 49

Side-Power SX100/185T

Brand: SLEIPNER MOTOR AS Pages: 16

Brand: Sleipner Pages: 28

Brand: Gigabyte Pages: 39

Brand: ASROCK Pages: 237

Brand: Daewoo Pages: 39

Brand: Gigabyte Pages: 53

Brand: AOpen Pages: 8

Brand: EPOX Pages: 83

Brand: DFI Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands