ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 4

Page: 4 / 178

TRGPS-9084GT-M12X-BP2-MV User

Manual

ORing Industrial Networking Corp

4.5

STP/RSTP/MSTP

............................................................................................................. 25

4.5.1

STP/RSTP

......................................................................................................................... 25

STP Bridge Status

........................................................................................................................... 26

STP Bridge Configurations

............................................................................................................ 28

4.5.2

MSTP

.................................................................................................................................. 29

Port Settings

.................................................................................................................................... 29

Mapping

............................................................................................................................................ 30

Priority

............................................................................................................................................... 31

4.5.3

CIST

.................................................................................................................................... 32

4.6

Fast Recovery

................................................................................................................... 34

Management ................................................................................................. 35

5.1

Basic Settings ................................................................................................................. 36

5.1.1

System Information ........................................................................................................ 36

5.1.2

Admin & Password ......................................................................................................... 37

5.1.3

Authentication Methods .................................................................................................. 38

5.1.4

IP Settings ....................................................................................................................... 38

5.1.5

IPv6 Settings ................................................................................................................... 39

5.1.6

Daylight Saving Time ..................................................................................................... 41

5.1.7

HTTPS ............................................................................................................................ 43

5.1.8

SSH ................................................................................................................................. 43

5.1.9

LLDP .............................................................................................................................. 44

5.1.10

Modbus TCP .............................................................................................................. 47

5.1.11

Backup/Restore Configurations ................................................................................. 48

5.1.12

Firmware Update ....................................................................................................... 48

5.2

DHCP Server .................................................................................................................. 48

5.2.1

Basic Settings

........................................................................................................ 48

5.2.2

Dynamic Client List

.............................................................................................. 49

5.2.3

Client List

................................................................................................................ 49

5.2.4

Relay Agent

............................................................................................................ 50

5.3

Port Setting ..................................................................................................................... 52

5.3.1

Port Control

............................................................................................................ 52

5.3.2

Port Trunk

............................................................................................................... 54

5.3.4

Loop Gourd

............................................................................................................. 58

5.4

VLAN ............................................................................................................................. 60

5.4.1

VLAN Membership

................................................................................................ 60

5.4.2

Port Configurations

.............................................................................................. 61

Introduction of Port Types

................................................................................................ 63

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands