manualshive.com logo in svg

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Share
Download
ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 177

 

TRGPS-9084GT-M12X-BP2-MV  User

 

Manual 

 

ORing Industrial Networking Corp 

176 

T

echnical Specifications 

ORing Switch Model

 

TRGPS-9084GT-M12X-BP2-MV

 

Physical Ports 

 

10/100/1000Base-T(X)  with P.S.E. 
Ports in M12 Auto MDI/MDIX 

8 (8-pin female X-coding) 

10/100/1000Base-T(X)  Ports in M12 
Auto MDI/MDIX 

4 (8-pin female X-coding) 

Technology 

 

Ethernet Standards

 

IEEE 802.3 for 10Base-T 
IEEE 802.3u for 100Base-TX 
IEEE 802.3ab for 1000Base-T 
IEEE 802.3x for Flow control 
IEEE 802.3ad for LACP (Link Aggregation Control Protocol) 
IEEE 802.1p for COS (Class of Service) 
IEEE 802.1Q for VLAN Tagging 
IEEE 802.1w for RSTP (Rapid Spanning Tree Protocol) 
IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol) 
IEEE 802.1x for Authentication 
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol) 
IEEE 802.3at PoE specification (up to 30 Watts per port for P.S.E.) 
IEEE 802.3af PoE specification (up to 15.4 Watts per port for P.S.E.) 

MAC Table 

8k

 

Jumbo frame  

Up to 9.6K Bytes 

Priority Queues 

8 

Processing 

Store-and-Forward 

Switch Properties 

Switching latency: 7 us 
Switching bandwidth: 24 Gbps 
Max. Number of Available VLANs: 4095 
VLAN ID range: VID 1 to 4094 
IGMP multicast groups: 128 for each VLAN 
Port rate limiting: User Define 

Security Features 

Device Binding security feature 
Enable/disable ports, MAC based port security 
Port based network access control (802.1x) 
MAC-based authentication (802.1x) 
VLAN (802.1Q) to segregate and secure network traffic 
Radius centralized password management 
SNMPv3 encrypted authentication and access security 
Https / SSH enhance network security 
Web and CLI authentication and authorization 
IP source guard 

Software Features 

IEEE 802.1D Bridge, auto MAC address learning/aging and MAC address (static) 
MSTP (RSTP/STP compatible) 
Redundant Ring (O-Ring) with recovery time less than 30ms 
TOS/Diffserv supported 
Quality of Service (802.1p) for real-time traffic 
VLAN (802.1Q) with VLAN tagging 
Guest VLAN 
IGMP v2/v3 Snooping 
Application-based QoS management 
DOS/DDOS auto prevention 
Port configuration, status, statistics, monitoring, security 
DHCP Server/Client/Relay 
SMTP Client 
Modbus TCP 

Network Redundancy

 

O-Ring  
O-Chain 
MRP

*NOTE

 

MSTP (RSTP/STP compatible) 

RS-232 Serial Console Port 

RS-232 in 5-pin M12 female A-coding connector with optional console cable which can be purchased separately. 
115200bps, 8, N, 1 

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands