ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 105

Page: 105 / 178

TRGPS-9084GT-M12X-BP2-MV User

Manual

ORing Industrial Networking Corp

104

Running

: analysis completes and ready for next move

Attacked

: DDOS attacks occur

Device Description

This page allows you to configure device description settings.

Label

Description

Device Type

Indicates device types. Possible types are:

---

: no specification

IP Camera

IP Phone

Access Point

PLC

Network Video Recorder

Location Address

Indicates location information of the device. The information can be

used for Google Mapping.

Description

Device descriptions

Stream Check

Stream check monitors the consistency of real-time network traffic from the device bound with

the port. When the traffic changes sharply all of a sudden, an alert will be issued. This page

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands