manualshive.com logo in svg

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Share
Download
ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 7

 

TRGPS-9084GT-M12X-BP2-MV  User

 

Manual 

 

ORing Industrial Networking Corp 

6 

G

etting Started 

1.1  About the TRGPS-9084GT-M12X-BP2-MV 

ORing’s TransporterTM series managed PoE Ethernet switches are designed for industrial 

applications, such as rolling stock, vehicle, and railway applications. 

 

TRGPS-9084GT-M12X-BP2-MV is 19” rack-mount managed Redundant Ring Ethernet switch 

with 8x10/100/1000Base-T(X) P.S.E. and 4x10/100/1000Base-T(X) ports which is specifically 

designed for the toughest and fully compliant with EN50155 requirement.    The switch support 

Ethernet Redundancy protocol, O-Ring (recovery time < 30ms over 250 units of connection), 

O-Chain, MSTP/RSTP/STP (IEEE 802.1s/w/D) can protect your mission-critical applications 

from network interruptions or temporary malfunctions  with its fast recovery technology.  

TRGPS-9084GT-M12X-BP2-MV  also support Power over Ethernet, a system to transmit 

electrical power up to 30 watts, along with data, to remote devices over standard twisted-pair 

cable  in an Ethernet network.  Each TRGPS-9084GT-M12X-BP2-MV  switch has 

8x10/100/1000Base-T(X) P.S.E. (Power Sourcing Equipment) ports.  P.S.E. is a device 

(switch or hub for instance) that will provide power in a PoE connection. 

 

TRGPS-9084GT-M12X-BP2-MV includes 2 sets of bypass ports that protect the network from 

failures and Network maintenance by ensuring network integrity during power loss.  And 

support wide operating temperature from -40

o

C to 75

o

C.  TRGPS-9084GT-M12X-BP2-MV 

can also be managed centralized  and convenient by Open-Vision, Except the Web-based 

interface, Telnet and console (CLI) configuration.    Therefore, the switch is one of the most 

reliable choices for EN50155 highly-managed Ethernet application.   

1.2  Software Features   

 

Supports O-Ring (recovery time < 30ms over 250 units of connection) and MSTP 

(RSTP/STP compatible) for Ethernet Redundancy 

 

Supports O-Chain that allows the device to operate in multiple redundant ring topologies 

 

Supports PoE scheduled configuration and PoE auto-ping check 

 

Supports IEEE 1588v2 clock synchronization   

 

Supports IPv6 new Internet protocol version 

 

Supports Modbus TCP protocol 

 

HTTPS/SSH protocols for higher network security 

 

Supports IEEE 802.3az Energy-Efficient Ethernet technology 

 

Supports SMTP client 

 

Supports IP-based bandwidth management 

 

Supports application-based QoS management 

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands