ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 102

Page: 102 / 178

TRGPS-9084GT-M12X-BP2-MV User

Manual

ORing Industrial Networking Corp

101

Attacked

: DDOS attacks occur

Device IP Address

Specifies IP address of the device

Device MAC

Address

Specifies MAC address of the device

Advanced Configurations

Alias IP Address

This page provides alias IP address configuration. Some devices might have more than one IP

addresses. You could specify other IP addresses here.

Label

Description

Alias IP Address

Specifies alias IP address. Keep

0.0.0.0

if the device does not have

an alias IP address.

Alive Check

Alive Check monitors the real-time status of the device connected to the port. live-checking

packets will be sent to the device to probe if the device is running. If the switch receives no

response from the device, actions will be taken according to your configurations.

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands