ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 117

Page: 117 / 178

TRGPS-9084GT-M12X-BP2-MV User

Manual

ORing Industrial Networking Corp

116

filter with the ACE, you can enter a specific TCP/UDP destination

range. A field for entering a TCP/UDP destination value appears.

TCP/UDP

Destination

Number

When

Specific

is selected for the TCP/UDP destination filter, you

can enter a specific TCP/UDP destination value. The allowed range

is 0 to 65535. A frame matching the ACE will use this TCP/UDP

destination value.

TCP/UDP

Destination Range

When

Range

is selected for the TCP/UDP destination filter, you can

enter a specific TCP/UDP destination range value. The allowed

range is 0 to 65535. A frame matching the ACE will use this

TCP/UDP destination value.

TCP FIN

Specifies the TCP FIN ("no more data from sender") value for the

ACE.

: TCP frames where the FIN field is set must not be able to match

this entry.

: TCP frames where the FIN field is set must be able to match this

entry.

Any

: any value is allowed ("

don't-care

").

TCP SYN

Specifies the TCP SYN ("synchronize sequence numbers") value for

the ACE

: TCP frames where the SYN field is set must not be able to match

this entry.

: TCP frames where the SYN field is set must be able to match this

entry.

Any

: any value is allowed ("

don't-care

").

TCP PSH

Specifies the TCP PSH ("push function") value for the ACE

: TCP frames where the PSH field is set must not be able to match

this entry.

: TCP frames where the PSH field is set must be able to match this

entry.

Any

: any value is allowed ("

don't-care

").

TCP ACK

Specifies the TCP ACK ("acknowledgment field significant") value for

the ACE

: TCP frames where the ACK field is set must not be able to match

this entry.

: TCP frames where the ACK field is set must be able to match this

entry.

Any

: any value is allowed ("

don't-care

").

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands