manualshive.com logo in svg

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Share
Download
ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 178

 

TRGPS-9084GT-M12X-BP2-MV  User

 

Manual 

 

ORing Industrial Networking Corp 

177 

 

LED Indicators 

 

Power Indicator (PWR) 

Green: Power LED x 1 

Ring Master Indicator (R.M.) 

Green: Indicates that the system is operating in O-Ring Master mode 

O-Ring Indicator (Ring) 

Green: Indicates that the system operating in O-Ring mode 
Green Blinking: Indicates that the Ring is broken. 

Fault Indicator (Fault) 

Amber: Indicate unexpected event occurred 

10/100/1000Base-T(X) M12 P.S.E. 
Port Indicator 

Top dual color LED for Ethernet speed indicator: Green LED for 1000Mbps, Amber for 100Mbps, Off for 10Mbps 
Middle Green LED for PoE enable indicator 
Bottom Green LED for port Link/Act indicator   

10/100/1000Base-T(X) M12 Port 
Indicator 

Top dual color LED for Ethernet speed indicator: Green LED for 1000Mbps, Amber for 100Mbps, Off for 10Mbps     
Bottom Green LED for Link/Act indicator 

Fault Contact 

 

Relay 

Relay output to carry capacity of 3A at 30VDC on 5-pin M12 female A-coding connector   

Power 

 

power input 

72/110 (50.4-137.5) VDC on 4-pin M12 male S-coding connector 

PoE Output Power 

60Watts 

Power consumption (Typ.) 

20Watts (not include PoE output) 

Overload current protection 

Present 

Reverse Polarity Protection 

Present 

Physical Characteristic 

 

Enclosure 

IP-30 

Weight (g) 

3,185 g 

Dimension (W x D x H) 

438 (W) x 250 (D) x 44 (H) mm (17.24x9.84x1.73 inch) 

Environmental 

 

Storage Temperature 

-40 to 85

o

C (-40 to 185

o

F) 

Operating Temperature 

-40 to 75

o

C (-40 to 167

o

F) 

Operating Humidity 

5% to 95% Non-condensing 

Regulatory Approvals 

 

EMC 

CE EMC (EN 55024, EN 55032), FCC Part 15B, EN 50155 (EN 50121-1, EN 50121-3-2) 

EMI 

EN 55032, CISPR32, EN 61000-3-2, EN 61000-3-3, FCC Part 15B class A 

EMS 

EN 55024 (IEC/EN 61000-4-2 (ESD), IEC/EN 61000-4-3 (RS), IEC/EN 61000-4-4 (EFT), 
IEC/EN 61000-4-5 (Surge), IEC/EN 61000-4-6 (CS), IEC/EN 61000-4-8(PFMF), IEC/EN 61000-4-11 (DIP)) 

Shock 

IEC60068-2-27 

Free Fall 

IEC60068-2-31 

Vibration 

IEC60068-2-6 

Safety 

EN60950-1 

Other 

EN 50155 (IEC 61373) 

MTBF 

298,128 hours 

Warranty 

5 years 

 

*NOTE: This function is available by 

 

 

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands