ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 26

Page: 26 / 178

TRGPS-9084GT-M12X-BP2-MV User

Manual

ORing Industrial Networking Corp

Note

: The maximum cable length for copper ports is 100 meters and 20km for fiber ports.

When data bypasses the inactive switch(s) to another active switch, the distance between the

two active switches must be within the maximum length, otherwise transmission will fail.

4.4 MRP

(Optional Function by Request)

4.4.1 Introduction

MRP

(Media Redundancy Protocol) is an

industry standard for high-availability

Ethernet networks. MRP allowing Ethernet switches in ring configuration to recover from

failure rapidly to ensure seamless data transmission. An MRP ring (IEC 62439) can support up

to 50 devices and will enable a back-up link in 80ms (adjustable to max. 200ms/500ms).

4.4.2 Configurations

Label

Description

Enable

Enables the MRP function

Manager

Every MRP topology needs a MRP manager. One MRP

topology can only have a Manager. If two or more switches are

set to be Manager, the MRP topology will fail.

React on Link Change

(Advanced mode)

Faster mode. Enabling this function will cause MRP topology to

converge more rapidly. This function only can be set in MRP

manager switch.

Ring Port

Chooses the port which connects to the MRP ring

Ring Port

Chooses the port which connects to the MRP ring

4.5 STP/RSTP/MSTP

4.5.1 STP/RSTP

STP (Spanning Tree Protocol), and its advanced versions RSTP (Rapid Spanning Tree

Protocol) and MSTP (Multiple Spanning Tree Protocol), are designed to prevent network loops

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands