ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 101

Page: 101 / 178

TRGPS-9084GT-M12X-BP2-MV User

Manual

ORing Industrial Networking Corp

100

Label

Description

Mode

Indicates the device binding operation for each port. Possible modes

are:

---

: disable

Scan

: scans IP/MAC automatically, but no binding function

Binding

: enables binding. Under this mode, any IP/MAC that does

not match the entry will not be allowed to access the network.

Shutdown

: shuts down the port (No Link)

Alive Check

Active

Check to enable alive check. When enabled, switch will ping the

device continually.

Alive Check

Status

Indicates alive check status. Possible statuses are:

---

: disable

Got Reply

: receive ping reply from device, meaning the device is still

alive

Lost Reply

: not receiving ping reply from device, meaning the device

might have been dead.

Stream Check

Active

Check to enable stream check. When enabled, the switch will detect

the stream change (getting low) from the device.

Stream Check

Status

Indicates stream check status. Possible statuses are:

---

: disable

Normal

: the stream is normal.

Low

: the stream is getting low.

DDoS Prevention

Acton

Check to enable DDOS prevention. When enabled, the switch will

monitor the device against DDOS attacks.

DDoS Prevention

Status

Indicates DDOS prevention status. Possible statuses are:

---

: disable

Analyzing

: analyzes packet throughput for initialization

Running

: analysis completes and ready for next move

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands