manualshive.com logo in svg

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Share
Download
ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 29

 

TRGPS-9084GT-M12X-BP2-MV  User

 

Manual 

 

ORing Industrial Networking Corp 

28 

Label 

Description 

Port 

The switch port number to which the following settings will be 

applied. 

RSTP 

The number of RSTP configuration BPDUs received/transmitted 

on the port 

STP 

The number of legacy STP configuration BPDUs 

received/transmitted on the port 

TCN 

The number of (legacy) topology  change  notification BPDUs 

received/transmitted on the port 

Discarded Unknown 

The number of unknown  spanning  tree BPDUs received (and 

discarded) on the port. 

Discarded Illegal 

The number of illegal spanning  tree BPDUs received (and 

discarded) on the port. 

Refresh 

Click to refresh the page immediately 

Auto-refresh 

Check  to enable an automatic refresh  of the page at regular 

intervals 

 

STP Bridge Configurations 

 

 

Label 

Description 

Protocol Version

 

The version of the STP protocol. Valid values include STP, RSTP 

and MSTP. 

Forward Delay

 

The delay used  by STP bridges to transit root and designated 

ports to forwarding (used in STP compatible mode). The range of 

valid values is 4 to 30 seconds. 

Max Age 

The maximum time the information transmitted by the root bridge 

is considered valid. The range of valid values is 6 to 40 seconds, 

and 

Max Age

 must be <= (FwdDelay-1)*2. 

Maximum Hop Count 

This defines the initial value of remaining  hops for MSTI 

information generated at the boundary of an MSTI region. It 

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands