Onicon FT-3100 Programming Manual Download Page 2

Page: 2 / 36

FT-3100 TRANSMITTER PROGRAMMING GUIDE

ONICON Incorporated 727.447.6140

Page 2

onicon.com

1.0 INTRODUCTION .........................................................................................................................5

1.1 Purpose of this Guide ...................................................................................................................................... 5

1.2 Display and User Interface ............................................................................................................................. 5

1.3 Accessing the Programming Menus .......................................................................................................... 6

2.0 QUICK START MENU ..................................................................................................................6

2.1 MENU - QUICK START ..................................................................................................................................... 7

Empty Pipe Detector [E.P.Detect=ON] .................................................................................................... 7

Empty Pipe Threshold [R max=kohm XXXX] ......................................................................................... 7

Scaled Pulse Output 2 [Pls2=Gal X.XXXX] ............................................................................................. 7

Output 2 Pulse Duration [Tpls2=ms X.XXXX] ........................................................................................ 8

Analog Output 1 Full Scale Value [A1S=Gal/m XXXXXX] ................................................................. 8

3.0 MAIN MENU ...............................................................................................................................9

3.1 MENU 1 - SENSOR ............................................................................................................................................ 9

Sensor Body Model [S.Model=XXX] ......................................................................................................... 9

Liner Material [Lining=XXXXXX] ...............................................................................................................10

Unit Type [U.type=XXXXXX] .......................................................................................................................10

Diameter [Diam.=XXX] .................................................................................................................................10

KA [KA=±XX.XXX] ..........................................................................................................................................10

KZ [KZ=±XXXX] ..............................................................................................................................................10

Empty Pipe Detector [E.P.Detect=ON] ..................................................................................................11

Empty Pipe Threshold [R max=kohm XXXX] .......................................................................................11

Electrode Cleaning [El. Cleaning=MIN] .................................................................................................11

Sensor Cable Length [S.cable=ft XXX] ...................................................................................................12

Alarm Delay Interval [S.err.delay=m XXX] ............................................................................................12

3.2 MENU 2 - UNITS .............................................................................................................................................13

Diameter Unit Type [Diam.=in] .................................................................................................................13

Remote Mount Cable Unit Type [S.cable=ft] ......................................................................................13

Flow Rate Unit Type [FR unit=IMPERIAL] .............................................................................................13

Pulse 1 Unit Type [Pl1 unit=IMPERIAL] ..................................................................................................14

Pulse 2 Unit Type [Pl2 unit=IMPERIAL] ...................................................................................................14

Total Forward Flow Totalizer Unit Type [T+ unit=IMPERIAL] ..........................................................14

Total Forward Flow Totalizer Units [T+ unit=Gal] ...............................................................................14

Total Forward Flow Totalizer Decimal Point Position [T+ D.P.=X] ................................................14

Partial Forward Flow Totalizer Unit Type [P+ unit=IMPERIAL] .......................................................14

Partial Forward Flow Totalizer Units [P+ unit=Gal] ............................................................................15

Partial Forward Flow Totalizer Decimal Point Position [P+ D.P.=X] .............................................15

Total Reverse Flow Totalizer Unit Type [T- unit=IMPERIAL] ............................................................15

Total Reverse Flow Totalizer Units [T- unit=Gal] .................................................................................15

Total Reverse Flow Totalizer Decimal Point Positiion [T- D.P.=X] .................................................15

Partial Reverse Flow Totalizer Unit Type [P- unit=IMPERIAL] .........................................................15

Partial Reverse Flow Totalizer Units [P- unit=Gal] ..............................................................................15

Partial Reverse Flow Totalizer Decimal Point Position [P- D.P.=X] ...............................................16

Temperature Unit Type [Temp. unit= °F] ................................................................................................16

Mass Units Enable [Mass units=OFF] ......................................................................................................16

Specific Gravity Coefficient [Sg=kg/dm

X.XXXX] ..............................................................................16

TABLE OF CONTENTS

Summary of Contents for FT-3100





































Search results

Summary of Contents for FT-3100

Reviews:

Related manuals for FT-3100

Brands by name

Popular brands

Onicon FT-3100, Programming Manual

Search results

Summary of Contents for FT-3100

Reviews:

Related manuals for FT-3100

Brands by name

Popular brands