Onicon FT-3100 Programming Manual Download Page 32

Page: 32 / 36

FT-3100 TRANSMITTER PROGRAMMING GUIDE

ONICON Incorporated 727.447.6140

Page 32

onicon.com

This function enables or disables the display of net totalizer data.

Note: This function is only available when negative totalizers are enabled [Neg.

tot.= ON] in DISPLAY menu (menu 9). When enabled, the following page is visible

on the display.

To change the existing setting, press enter to access the function and use the up

arrow key to turn the function on or off. Press enter to accept the change and

exit the function. Press escape to exit the program mode.

Table of Contents

This function enables or disables the display of the quick start menu page.
To change the existing setting, press enter to access the function and use the up

arrow key to turn the function on or off. Press enter to accept the change and

exit the function. Press escape to exit the program mode.

Table of Contents

Enable Net Totalizers

[Net tot. = OFF]

Enable Quick Start Menu

[Quick start = ON]

2 ALARM(S)

+0.000

-0.204

Gal/m

Gal
Gal

Summary of Contents for FT-3100





































Search results

Summary of Contents for FT-3100

Reviews:

Related manuals for FT-3100

Brands by name

Popular brands

Onicon FT-3100, Programming Manual

Search results

Summary of Contents for FT-3100

Reviews:

Related manuals for FT-3100

Brands by name

Popular brands