Onicon FT-3100 Programming Manual Download Page 6 | Manualshive

Page: 6 / 36

background image

FT-3100 TRANSMITTER PROGRAMMING GUIDE

ONICON Incorporated 727.447.6140

Page 6

onicon.com

The most commonly used programming functions are available in the Quick Start

menu. The menu can be accessed by briefly pressing the

key and entering

the access code 4*******. Additional programming options are accessed via the

Access to the programming menus is password protected. The factory default

access code is 4********. The three user interface push-button functions described

below change when operating in the program mode.

1.3 ACCESSING THE

PROGRAMMING MENUS

SECTION 2.0:

QUICK START MENU

1. From the main screen, quickly press the

2. Enter the access code.

3. Enter into the Quick Start menu.

Push Button

Short Press

(<1 second)

(>1 second)

• Increments the numeric value or selected

• Returns to the previous menu item

• Decrements the numeric value

• Advances to the next menu item

Moves the cursor to the right on input fields

• Advances to the next menu item

• Changes the process data display

Moves the cursor to the left on input fields

• Returns to the previous menu item

• Enters or leaves the selected function

• Enters the program mode

• Cancels the selected function in progress

• Exits the current menu

Confirms the selected function to enable the

totalizer reset request, when enabled.

ACCESS CODE

QUICK START

E. P. Detect=

«
...
4
5
6
7
8
...
»

Summary of Contents for FT-3100





































Reviews:

No comments

Related manuals for FT-3100

Brand: Easy wave Pages: 2

Brand: Security Brands Pages: 3

Brand: Leuze electronic Pages: 61

Brand: Tellur Pages: 7

Brand: Keysight Technologies Pages: 39

Brand: Ebyte Pages: 56

Brand: You Ting Technology Pages: 16

Brand: Endress+Hauser Pages: 26

Brand: Omega Pages: 20

A25C SPORT 66 USA

Brand: Icom Pages: 4

Brand: Phoenix Contact Pages: 24

Brand: SVP Pages: 165

Brand: Lumel Pages: 89

Brand: Wouxun Pages: 39

Brand: Motorola solutions Pages: 100

Brand: MELICONI Pages: 24

Brand: Camille Bauer Pages: 2

PASCAL CS21 0 Series

Brand: Labom Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands