Omron WS02-NCTC1-E - 07-2001 Operation Manual Download Page 79

Page: 79 / 116

FinsGateway Configuration and Startup

Section 6-2

Configuring the Protocol
and Node

For Host Link, the protocol must be changed to SYSWAY-CV from the default,
(SYSWAY). The node number must match the node number used when the
PC was added to CX-Position.

1,2,3...

Click the

Nodes

Tab.

Set the node to 240 (shown in reverse video).

Click the

Property

Button.

Set the following configurations in the Add/Edit Serial Node Window.

• The node number must match the node number used under

Networks

when the PC was added to CX-Position.

• The

Type

can be left as C200H.

FinsGateway

default setting

Adding PC to CX-

Position

PC addition default

setting

Node...

on the

Nodes

Tab

Page.

240

Node Number

under

Network Settings

Must be set to 240 if
FinsGateway is the
default.

Summary of Contents for WS02-NCTC1-E - 07-2001





















































































































Search results

Summary of Contents for WS02-NCTC1-E - 07-2001

Reviews:

Related manuals for WS02-NCTC1-E - 07-2001

Brands by name

Popular brands

Omron WS02-NCTC1-E - 07-2001, Operation Manual

Search results

Summary of Contents for WS02-NCTC1-E - 07-2001

Reviews:

Related manuals for WS02-NCTC1-E - 07-2001

Brands by name

Popular brands