Omron WS02-NCTC1-E - 07-2001 Operation Manual Download Page 77

Page: 77 / 116

Default Configurations for Connecting Online

Section 6-1

6-1

Default Configurations for Connecting Online

Online connection enables using the following CX-Position software functions.

• Download to NC

• Upload from NC

• Verify

• Write Flash Memory

• Monitor

• Monitor Units

• Monitor NC Operating Memory Area

• Monitor NC Operating Data Area

• View NC Error Log

The following FinsGateway settings are required to connect the CX-Position
software online to a PC using serial communications (with the Host Link pro-
tocol) and execute the functions in the previous list.

6-1-1

Connecting via Host Link (SYSWAY-CV)

CPU and NC Unit
Default Configuration

1,2,3...

Set the NC Unit’s unit number (using the front-panel rotary switches)

Create the I/O tables (using the CX-Programmer or Programming Con-
sole)

Set the DIP switch on the CPU Unit’s front panel.

• If using a peripheral port, turn ON pin 4, and set the PC Setup (set Pro-

gramming Console address 144 to the 0000 Hex default, if not already
set to it).

• If using an RS-232C port, turn OFF pin 5, and set the PC Setup (set

Programming Console address 160 to the 0000 Hex default, if not al-
ready set to it).

FinsGateway
Configuration and
Startup

Refer to

6-2 FinsGateway Configuration and Startup

for details.

6-2

FinsGateway Configuration and Startup

6-2-1

Standard Configuration and Startup Procedure

The following are the standard configuration and startup procedures.

1,2,3...

From the

Start

Menu, select

Programs/FinsGateway/FinsGateway Con-

figuration

Double-click each communications driver under

Networks/Drivers

on the

Basic

Tab Page and set the required configuration (e.g., the COM Port,

protocol, communications parameters, and other settings). The following
FinsGateway configurations must match the

Network Configuration

config-

urations set when the PC was added to CX-Position.

FinsGateway

Adding a PC to CX-Position

Network number

under the

Network

Tab’s

Network

Network Address

under

Network Settings

Node...

in the

Nodes

Tab.

Node Number

under

Network Settings

Summary of Contents for WS02-NCTC1-E - 07-2001





















































































































Search results

Summary of Contents for WS02-NCTC1-E - 07-2001

Reviews:

Related manuals for WS02-NCTC1-E - 07-2001

Brands by name

Popular brands

Omron WS02-NCTC1-E - 07-2001, Operation Manual

Search results

Summary of Contents for WS02-NCTC1-E - 07-2001

Reviews:

Related manuals for WS02-NCTC1-E - 07-2001

Brands by name

Popular brands