background image

93

NC Unit Error Logs

Section 10-1

Data Check at Startup

The following table shows the errors checked when power is turned ON.

Group

Name

 Code

Cause

Remedy

Data destruc-
tion

Parameters destruc-
tion

0001

When using the axis parameters in 
the NC Unit, the parameters saved 
in flash memory are lost. It is pos-
sible that, while saving to flash 
memory, the NC Unit’s power sup-
ply was interrupted, there was 
noise, or there was an error in 
flash memory.

In this condition, only the data 
transfer (read and write) and data 
save operations can be performed. 
The NC Unit’s axis parameters and 
data are all returned to their 
default values. After transferring 
the parameters and data for all 
axes, save the parameters and 
either reset the power supply, or 
restart the Unit. If the error per-
sists, it is possible that there is a 
fault in flash memory, and so it 
may be necessary to replace the 
NC Unit.

Data destruction

0002

The following data saved in flash 
memory will be lost:

Zones, positioning sequences, 
speeds, acceleration/deceleration 
data, positions, and dwell times.

It is possible that, while saving to 
flash memory, the NC Unit’s power 
supply was interrupted, there was 
noise, or there was an error in 
flash memory.

F-ROM check data 
destruction

0003

The flash memory error data 
saved in flash memory is lost 
(OMRON maintenance data is 
lost).

It is possible that, while saving to 
flash memory, the NC Unit’s power 
supply was interrupted, there was 
noise, or there was an error in 
flash memory.

When this error occurs, operation 
can be continued by performing 
error reset. Execute the next oper-
ation after performing error reset.

Common 
parameters

Operating data area 
designation error

0010

The operating data area designa-
tion (m) is incorrect.

 Area designation: Set to a setting 

other than 00, 0D, or 0E.

 Bank designation: Set to a set-

ting not in the range 00 to 0C, 
when 0E is set for the area desig-
nation.

In this condition, only the data 
save operations can be performed. 
All of the axes’ parameters and all 
data will be returned to their 
default values. After correcting the 
common parameters, (refer to 

SECTION 4

), reset the power sup-

ply or restart the NC Unit.

Operating data area 
address designation 
error

0011

The designation of the beginning 
word of the operating data area’s 
address (m+1) is outside the setta-
ble range.

Parameter designa-
tion error

0013

The axis parameter designation 
(m+2) is not set to 00 or 01.

Axis designation 
error

0014

The axis parameter designation 
(m+2) is set to 01, but 1 is set for 
an axis other than that for a 1-axis, 
2-axis or 4-axis Unit.

Axis parame-
ters

Response timeout

0020

The axis parameters set in the 
CPU Unit could not be read to the 
NC Unit.

Increase the cycle monitor time set 
with CX-Programmer and either 
reset the power supply or restart 
the NC Unit. If this error occurs 
again, despite increasing the cycle 
monitor time, it is possible that 
there is a fault in the NC Unit or 
somewhere in the PC. Either 
replace the whole PC, or the NC 
Unit.

Summary of Contents for WS02-NCTC1-E - 07-2001





















































































































Reviews: