When Performing 3D Measurement
Coordinates from two cameras must be linked when performing 3D measurement. This
operation is called "3D coordinate setting".
When using all-in-one cameras
When the distance between the measurement objects and the camera position is
small (300 mm or less), the 3D measurement can be performed with all-in-one
cameras. All-in-one cameras do not require specific settings since the 3D
coordinate parameter was set at the factory.
However, if the precision of measurement is not accurate, you may need to re-
registrate the 3D coordinate parameter according to the installation environment.
When using separate-type cameras
When the distance between the measurement object and the camera position is big
(more than 300 mm), use separate-type cameras. Separate-type cameras require
the 3D coordinate setting.
3D Coordinate Registration
3D measurement is performed with a combination of two or three cameras. In order to
accurately measure the height direction, the position of each camera must be accurately
identified and the coordinates of two cameras must be linked. This procedure is referred
to as "3D coordinate setting" and a custom calibration tool must be used. Please prepare a
calibration tool beforehand.
There are two methods for making a 3D coordinate setting:
Settings when the calibration target can be placed horizontally.
Settings when the calibration target cannot be placed in horizontally.
Settings when the calibration target can be placed horizontally.
Take samples of the calibration target at 2 points, close and long distance from the
camera. Set 3D coordinates by registering each position.
Summary of Contents for FZ2 Series
