E
Error input range. Please
input correctly.
Please verify settable range for re-setting.
Fan/voltage error.
Switch off controller, and verify if fan is affected. If Error
information is also shown after restart, the controller may
be damaged. Please contact our regional branches and
regional offices.
Failed to clear scene
group
Confirm that a USB disk is set to the controller and try
again.
Failed to save file Check
the destination.
Check the following points.
Is the capacity of the destination enough?
Is the USB disk set to the controller, while the save
destination is set to a folder on the USB disk? Or,
the controller may not have detected the USB disk.
Failed to start the
window. Memory may
be insufficient.
The memory necessary to start the window could not be
secured, since available memory is not enough. Check the
flow by adjusting the measured region of each processing
unit and the sizes of the registered models.
Failed to switch scene
Is a USB disk set to the controller?
To load the scenes of Scene Group 1 and later, a USB disk
is necessary.
F
Failed to switch scene
group or failed to save
when switching scene
group
The cause of the failure to switch or to save when
switching may be that the USB disk was removed from the
controller. Set a USB disk to the controller and try again.
I
Illegal expression
Are there the following Errors in settings of expression?
Different number of left/right parentheses
Connecting separately to
TJG/Unit/value/function/operator/comma
Operator is set at beginning or end of expression
Insufficient or extreme function parameters
L
Low disk space. Please
check.
Please delete unnecessary scenes and ProUnits.
Please use scene set function and reduce the
number of scenes registered into a scene set.
N
No value set. Please set
value.
This item must be set. Please set up value.
S
System date setting
Low battery (for the backup of date and time data) level.
Summary of Contents for FZ2 Series
