manualshive.com logo in svg

Omron E5 C Series, Manual

Share
Download
Omron E5 C Series Manual Download Page 130

E5

@

C/E5

@

C-T

130

Mounting the Terminal Cover
E5CC/E5CC-T

Slightly bend the E53-COV23 Terminal Cover to attach it to the 
terminal block as shown in the following diagram. The Terminal Cover 
cannot be attached in the opposite direction. E53-COV17 Terminal
 Cover can be also attached.
Make sure that the "UP" mark is facing up, and then attach the E53-
COV17 Terminal Cover to the holes on the top and bottom of the 
Digital Temperature Controller.

E5EC/E5AC/E5EC-T/E5AC-T

Slightly bend the E53-COV24 Terminal Cover to attach it to the 
terminal block as shown in the following diagram. The Terminal Cover 
cannot be attached in the opposite direction.

Attaching the End Cover
E5DC/E5DC-B

1.

Install the E5DC/E5DC-B in a panel.

2.

Peel off the release paper from the double-sided tape on the End 

Cover.

3.

Align the tabs on the End Cover with the depressions on the 

E5DC/E5DC-B and attach the End Cover.

4.

Secure the End Cover so that the double-sided tape is firmly 

attached.

Adapter

Terminal Cover
 (E53-COV17)
(Sold separately)

E53-COV17

E53-COV23

Enlarged illustration of 
Terminal Section

Enlarged illustration of the terminal part

Slightly bend the 
E53-COV24 Terminal 
Cover in the direction 
shown by the arrows to 
attach it to the terminal block.

Double-sided tape

Summary of Contents for E5 C Series










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands