manualshive.com logo in svg

Omron E5 C Series, Manual

Share
Download
Omron E5 C Series Manual Download Page 129

E5

@

C/E5

@

C-T

129

2.

Remove the Main Unit from the Terminal Unit.

3.

Remove the Terminal Units.

Removing the Connector Cover
E5DC-B

1.

For both male and female covers, insert the tip of a flat-blade 

screwdriver into the cutout on the connector cover to remove the 

connector cover.

Attaching the Connector Cover
E5DC-B
For male connector covers

1.

Press on the connector cover until it clicks into place. There is no 

vertical direction for male connector covers.

For female connector covers

1.

Insert the projecting part on the female connector cover into the 

groove on the terminal unit.

2.

Press on the female connector cover until it clicks into place in the 

cutout.

Mounting the DIN Track

Attach the DIN Track to the inside of the control panel with screws to 
at least three locations.

• DIN Track (sold separately)

PFP-50N (50 cm) and PFP-100N (100 cm)

Install the DIN Track vertically to the ground.

(2)

(3)

Cutout

Male connector cover

Cutout

Female connector cover

(1)

Projection Part

Groove

(1)

Cutout

(2)

Vertical: OK

Horizontal: NG

Summary of Contents for E5 C Series










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands