![background image](http://html1.mh-extra.com/html/omega/omp-modl/omp-modl_user-manual_4017938063.webp)
3... I
NTERFACE
M
ODULES
U
SING THE
OMP-MODL
3-39
Each switch bank should have only ONE switch ON and the other four
switches OFF.
CAUTION:
The switch banks may have different numbering than the circuit
board...
insure that the marking on the circuit board is followed
... not the
marking on the switch banks.
Hardware Input Configuration Switches:
No hardware input configuration switches are provided on the MLIM-4. All
configuration is done via the HyperNet software.
Software Configuration of the MLIM-4
The MLIM-4 module is completely configured on a channel by channel basis
from within the HyperNet software. This software configuration and
utilization of the various MLIM-4 channels in a Program Net is covered in
overview in Chapter 6, within the Master Icon Listing in Appendix A, and with
specific detail in this document.
When the MLIM-4 module is detected in a OMP-MODL after clicking on the
New Program
button from within HyperNet, four icons representing the
MLIM-4 input channels will display on the screen. The icons will display as
2-wire RTD inputs as the default. These icons can be switched to
Resistance or Thermistor inputs by double-clicking on the icon to open the
configuration dialog then on the
Change
button.
ml051
Module 3
Module 2
Module 4
Module 5
Module 6
OFF - ON
OFF - ON
OFF - ON
Module Address (Layer) Switch banks
Figure 3... -27: Example Address setting for Module Layer Position 4
Summary of Contents for OMP-MODL
